Preparation temperature, effect

Al Ti in the range of 0.9—1.0 appeared optimum for i7j -l,4-polyisoprene yield (20). Other factors such as catalyst preparation temperature, influence of the R group in the alkyl aluminum compound (R Al), and catalyst aging have been extensively studied (16,17). Another variable studied was the effect of... 

It should be noted that the properties of a CTC depend to a considerable degree on the conditions of their preparation. Temperature increase, in particular, favors the accumulation of complete charge transfer states in a CTC. In the case of a CTC obtained in solution, the increase of dielectric constant of the solvent has the same effect. The method of preparation of a CTC also affects the kinetic curves of the accumulation and depletion of complete transfer states arising at protoirradiation. 

Dubau L, Coutanceau C, Gamier E, Leger JM, Lamy C. 2003a. Electrooxidation of methanol at platinum-mthenium catalysts prepared from colloidal precursors Atomic composition and temperature effects. J Appl Electrochem 33 419-429. 

Selected entries from Methods in Enzymology [vol, page(s)] Theory, 63, 340-352 measurement, 63, 365 cryosolvent [catalytic effect, 63, 344-346 choice, 63, 341-343 dielectric constant, 63, 354 electrolyte solubility, 63, 355, 356 enzyme stability, 63, 344 pH measurements, 63, 357, 358 preparation, 63, 358-361 viscosity effects, 63, 358] intermediate detection, 63, 349, 350 mixing techniques, 63, 361, 362 rapid reaction techniques, 63, 367-369 temperature control, 63, 363-367 temperature effect on catalysis, 63, 348, 349 temperature effect on enzyme structure, 63, 348. 

R. Iwamoto, S. Hidaka, I. Nakamura and A. lino Effect of preparation temperature... 

The robustness of an analytical procedure is a measure of its capacity to remain unaffected by small but deliberate variations in the analytical procedure parameters. The robustness of the analytical procedure provides an indication of its reliability during normal use. The evaluation of robustness should be considered during development of the analytical procedure. If measurements are susceptible to variations in analytical conditions, the analytical conditions should be suitably controlled or a precautionary statement should be included in the procedure. For example, if the resolution of a critical pair of peaks was very sensitive to the percentage of organic composition in the mobile phase, that observation would have been observed during method development and should be stressed in the procedure. Common variations that are investigated for robustness include filter effect, stability of analytical solutions, extraction time during sample preparation, pH variations in the mobile-phase composition, variations in mobile-phase composition, columns, temperature effect, and flow rate. 

Temperature Effects The pH of a buffer solution is influenced by temperature. This effect is due to a temperature-dependent change of the dissociation constant (pK ) of ions in solution. The pH of the commonly used buffer Tris is greatly affected by temperature changes, with a ApKa/C° of —0.031. This means that a pH 7.0 Tris buffer made up at 4°C would have a pH of 5.95 at 37°C. The best way to avoid this problem is to prepare the buffer solution at the temperature at which it will be used and to standardize the electrode with buffers at the same temperature as the solution you wish to measure. 

Another unusual temperature effect is observed in comparing the intrinsic viscosity of polymer prepared with chemical initiators at a series of temperatures from 25° to 100° (7, 126). A distinct maximum appears at a temperature of preparation in the 50° to 60° range, whereas one expects a monotonic decline with temperature. 

Molecular self-organization in solution depends critically on molecular structural features and on concentration. Molecular self-organization or aggregation in solution occurs at the critical saturation concentration when the solvency of the medium is reduced. This can be achieved by solvent evaporation, reduced temperature, addition of a nonsolvent, or a combination of all these factors. Solvato-chromism and thermochromism of conjugated polymers such as regioregular polythiophenes are two illustrative examples, respectively, of solubility and temperature effects [43-45]. It should therefore be possible to use these solution phenomena to pre-establish desirable molecular organization in the semiconductor materials before deposition. Our studies of the molecular self-assembly behavior of PQT-12, which leads to the preparation of structurally ordered semiconductor nanopartides [46], will be described. These PQT-12 nanopartides have consistently provided excellent FETcharacteristics for solution-processed OTFTs, irrespective of deposition methods. 

To verify the effect of the ions adsorption on the regularities of photoexcitation relaxation, we studied the temperature effect on the kinetics of the ultradispersed CdS photobleaching relaxation at the addition of electron acceptors of various nature. Fig. 2.13 presents the kinetic curves of the colloidal CdS photobleaching relaxation prepared with an excess of cadmium ions at different temperatures and at the addition of different... 

The PTC effect is distinguished from the majority of other critical temperature effects in the ease with which the critical temperature can be shifted by altering the composition. The replacement of barium in BaTiC>3 by strontium lowers the critical temperature by 4°C per percentage atomic replacement, whilst replacement by lead raises the critical temperature by 4.3 °C per percentage atomic replacement (see Fig. 2.47). Since the critical temperature for BaTiC>3 is 120-130 °C, it is a simple matter to prepare ceramics with PTC regions anywhere between -100 °C and +250 °C, although the highest temperature coefficients are found in barium titanate compositions without major quantities of substituents. 

The HLB system used above does not take into consideration the temperature effects. Upon heating, an O/W emulsion prepared with nonionic surfactants inverts to a W/O emulsion because the hydrogen bondings in the polyoxyethylene groups are broken, and the HLB value of the surfactant becomes smaller. The higher the... 

---