Potassium hydroxide, solid

Potassium hydroxide. Solid potassium hydroxide is very rapid and efficient. Its use is limited almost entirely to the initial drying of organic bases. Alternatively, sometimes the base is shaken first with a concentrated solution of potassium hydroxide to remove most of the water present. Unsuitable for acids, aldehydes, ketones, phenols, amides and esters. Also used for drying gaseous amines and ammonia. 

SulfenylatioH of nitriles. Potassium hydroxide (solid) suspended in THF generates the a-carbanion of nitriles. Thus nitriles in THF can be sulfenylated generally in yields of 80-987, by treatment with KOH followed by addition of a disulfide (equation I). 

Batteries, Dry, Containing Potassium Hydroxide, Solid Series of metal plates immersed in dry potassium hydroxide in a closed receptacle. IMO 8119... 

Batteries, Dry, Containing Potassium Hydroxide, Solid. Storage batteries filled with potassium hydroxide, solid which are shipped from the factory in their original dry state and filled with the dry alkali. Water would be added to the battery before first being used. ICAO A2, lATA App. A... 

Fig. 3. Conductivity of two-component PP-g-PAA membranes plotted against the conductivity of ambient solution (potassium hydroxide). Solid line calculated according to Eq. (5). Volume fraction of PAA in dry membrane A - 26%, B - 36%,...

X) 60 BATFERIES. dry, coniaining POTASSIUM HYDROXIDE solid (electric storage)... 

Propylene oxide has an asymmetric carbon atom. The normal commercial epoxide is a racemic mixture of the d- and 1-isomers. Osgan and Price did extensive work with both the 1-propylene oxide and the d,l-propylene oxide in both potassium hydroxide and ferric chloride/propylene oxide-initiated polymerizations. Their results are summarized in Table 5 (48). C. C. Price and coworkers first demonstrated that polymerization of pure 1-propylene oxide with an anhydrous potassium hydroxide (solid KOH) initiator led to a crystalline, rather than the usual amorphous, liquid, polymer. After extensive study by a number of researchers (69), this polymerization was shown to proceed by a stepwise anionic mechanism. The uses found for polymers of propylene oxide largely have been those requiring the amorphous polymer in elastomeric applications. Stereospecificity, however, has proved to be a key tool in understanding the polymerization mechanisms. 

Aluminium oxide is a white solid, insoluble in water, with a very high melting point. If heated above red heat, it becomes insoluble in acids and alkalis, and can only be brought into solution by first fusing it with sodium or potassium hydroxide when an aluminate is formed. 

The benzene used in this preparation should be reasonably free from toluene therefore use a sample of benzene supplied by dealers as crystalUsable benzene, i.e.y one which crystallises readily when cooled in ice-water. It should preferably be dried over calcium chloride and, immediately before use, filtered through a fluted filter-paper. The pyridine should also preferably be dried over solid potassium hydroxide and redistilled. 

Potassium Hydroxide, Alcoholic. Boil under reflux a mixture of 10 g. of powdered KOH and 100 ml. of rectified spirit for 30 minutes. Cool and if solid material remains, decant through a filter of glass-wool. 

Into a 500 ml. round-bottomed flask, fitted with a reflux condenser, place 42 g. of potassium hydroxide pellets and 120 g. (152 ml.) of absolute ethyl alcohol. Heat under reflux for 1 hour. Allow to cool and decant the liquid from the residual solid into another dry 500 ml. flask add 57 g. (45 ml.) of A.R. carbon dtsulphide slowly and with constant shaking. Filter the resulting almost solid mass, after cooling in ice, on a sintered glass funnel at the pump, and wash it with two 25 ml. portions of ether (sp. gr. 0-720), followed by 25 ml. of anhydrous ether. Dry the potassium ethyl xanthate in a vacuum desiccator over silica gel. The yield is 74 g. If desired, it ma be recrystallised from absolute ethyl alcohol, but this is usually unneceasary. 

Dimethylaminomethylindole (gramine). Cool 42 5 ml. of aqueous methylamine solution (5 2N ca. 25 per cent, w/v) contained in an 100 ml. flask in an ice bath, add 30 g. of cold acetic acid, followed by 17 -2 g. of cold, 37 per cent, aqueous formaldehyde solution. Pour the solution on to 23 -4 g. of indole use 10 ml. of water to rinse out the flask. Allow the mixture to warm up to room temperature, with occasional shaking as the indole dissolves. Keep the solution at 30-40° overnight and then pour it, with vigorous stirring, into a solution of 40 g. of potassium hydroxide in 300 ml. of water crystals separate. Cool in an ice bath for 2 hours, collect the crystalline solid by suction flltration, wash with three 50 ml. portions of cold water, and dry to constant weight at 50°. The yield of gramine is 34 g. this is quite suitable for conversion into 3-indoleacetic acid. The pure compound may be obtained by recrystaUisation from acetone-hexane m.p. 133-134°. 

Diethylene glycol method. Place 0-5 g. of potassium hydroxide pellets, 3 ml. of diethylene glycol and 0 5 ml. of water in a 10 or 25 ml. distilling flask heat the mixture gently until the alkali has dissolved and cool. Add 1-2 g. of the ester and mix well. Fit the flask with a thermometer and a small water-cooled condenser in the usual way. Heat the flask over a small flame whilst shaking gently to mix the contents. When only one liquid phase, or one hquid phase and one solid phase, remains in the flask, heat the mixture more strongly so that the alcohol distils. Identify the alcohol in the distillate by the preparation of the 3 5 dinitrobenzoate (Section 111,27,2). 

The oxaziridine ring itself is stable towards alkali there is, for instance, no substitutive ring opening by hydroxyl ions as in oxiranes. 2-r-Butyl-3-phenyloxaziridine (56) is not attacked by methoxide ion in methanol during 12 h at room temperature 3-isopropyl-2-r-octyloxaziridine does not react at room temperature with either solid potassium hydroxide or potassium methoxide solution (57JA5739). 

The contents of the flask while still hot are poured into a 30-cm. evaporating dish and the alcohol is evaporated on a steam bath. The dry salt is pulverized and thoroughly mixed with 390 g. of calcium oxide, placed in a 2-I. copper retort (Note 3), and heated with the full flame of a Meker burner. The distillate is placed in a distilling flask and heated on a steam bath all material distilling under 90 is removed and discarded. The residue is then allowed to stand over solid potassium hydroxide for twelve hours and is finally fractionated. The dimethyl-pyridine distils at i42-i44°/743 mm. The yield is 35-36 g. or 62-64 per cent of the theoretical amount based on the 3,5-dicarb-ethoxy-2,6-dimethylpyridine, or 30-36 per cent based on the original ethyl acetoacetate. 

---