Hydrogen bonding polypeptides

FIGURE 24.11 A representation of the a-helical structure of a polypeptide. Hydrogen bonds are denoted... 

Figure 24.11 A representation of the a-helical structure of a polypeptide. Hydrogen bonds are denoted by dashed lines. (Illustration, Irving Geis. Rights owned by Howard Hughes Medical Institute. Not to be reproduced without permission.)...

Although hydrogen bonds ate weak interactions, they are the single most important force determining the three-dimensional folding of proteins. The a-helix and the j0-pleated sheet, two of the proposed polypeptide hydrogen bonding schemes, have been found to be the most recurrent features that stabilize the secondary structures of proteins. 

Pauling L, R B Corey and H R Bronson 1951. The Structure of Proteins Two Hydrogen-bonded He Configurations of the Polypeptide Chain. Proceedings of the National Academy of Sciences USA y . 211... 

Section 27 19 Two secondary structures of proteins are particularly prominent The pleated sheet is stabilized by hydrogen bonds between N—H and C=0 groups of adjacent chains The a helix is stabilized by hydrogen bonds within a single polypeptide chain... 

Fig. 5. Protein folding. The unfolded polypeptide chain coUapses and assembles to form simple stmctural motifs such as -sheets and a-hehces by nucleation-condensation mechanisms involving the formation of hydrogen bonds and van der Waal s interactions. Small proteins (eg, chymotrypsin inhibitor 2) attain their final (tertiary) stmcture in this way. Larger proteins and multiple protein assembhes aggregate by recognition and docking of multiple domains (eg, -barrels, a-helix bundles), often displaying positive cooperativity. Many noncovalent interactions, including hydrogen bonding, van der Waal s and electrostatic interactions, and the hydrophobic effect are exploited to create the final, compact protein assembly. Further stmctural...

Fig. 2. Protein secondary stmcture (a) the right-handed a-helix, stabilized by intrasegmental hydrogen-bonding between the backbone CO of residue i and the NH of residue t + 4 along the polypeptide chain. Each turn of the helix requires 3.6 residues. Translation along the hehcal axis is 0.15 nm per residue, or 0.54 nm per turn and (b) the -pleated sheet where the polypeptide is in an extended conformation and backbone hydrogen-bonding occurs between residues on adjacent strands. Here, the backbone CO and NH atoms are in the plane of the page and the amino acid side chains extend from C ...

Pauling, L., Corey, R.B., Branson, H.R. The structure of proteins two hydrogen-bonded helical configurations of the polypeptide chain. Proc. Natl. Acad. Sd. USA 37 205-211, 1951. 

Figure 11.14 Schematic diagram of the active site of subtilisin. A region (residues 42-45) of a bound polypeptide inhibitor, eglin, is shown in red. The four essential features of the active site— the catalytic triad, the oxyanion hole, the specificity pocket, and the region for nonspecific binding of substrate—are highlighted in yellow. Important hydrogen bonds between enzyme and inhibitor are striped. This figure should be compared to Figure 11.9, which shows the same features for chymotrypsin. (Adapted from W. Bode et al., EMBO /.

FIGURE 5.8 Two structural motifs that arrange the primary structure of proteins into a higher level of organization predominate in proteins the a-helix and the /3-pleated strand. Atomic representations of these secondary structures are shown here, along with the symbols used by structural chemists to represent them the flat, helical ribbon for the a-helix and the flat, wide arrow for /3-structures. Both of these structures owe their stability to the formation of hydrogen bonds between N—H and 0=C functions along the polypeptide backbone (see Chapter 6). 

If the protein of interest is a heteromultimer (composed of more than one type of polypeptide chain), then the protein must be dissociated and its component polypeptide subunits must be separated from one another and sequenced individually. Subunit associations in multimeric proteins are typically maintained solely by noncovalent forces, and therefore most multimeric proteins can usually be dissociated by exposure to pEI extremes, 8 M urea, 6 M guanidinium hydrochloride, or high salt concentrations. (All of these treatments disrupt polar interactions such as hydrogen bonds both within the protein molecule and between the protein and the aqueous solvent.) Once dissociated, the individual polypeptides can be isolated from one another on the basis of differences in size and/or charge. Occasionally, heteromultimers are linked together by interchain S—S bridges. In such instances, these cross-links must be cleaved prior to dissociation and isolation of the individual chains. The methods described under step 2 are applicable for this purpose. 

---