Polymers from chain reactions

Because of some fundamental differences in polymer structures produced by the modes of polymerization, polymer molecules are also classified by the synthetic routes through which they were obtained (8). Polymers from chain-reaction polymerizations are often called chain-growth polymers (previously known as addition polymers) and polymers from step reaction-polymerizations are often called step-growth polymers (previously condensation polymers). 

Polymers from step-reaction polymerizations have structures that are far more uniform than those prepared by chain-reaction polymerizations. The molecular weight distributions obtained are narrow. Examples are nylons, polyesters and polyurethanes. The structures can be determined directly by infrared or nuclear magnetic resonance techniques or after hydrolysis and isolation of the monomers used in polymerization. 

In the next group of chapters we shall discuss condensation or step-growth polymers and polymerizations in Chap. 5, addition or chain-growth polymers and polymerizations in Chap. 6, and copolymers and stereoregular polymers in Chap. 7. It should not be inferred from this that these are the only classes of polymers and polymerization reactions. Topics such as ring-opening polymeri-... 

The kind of reaction which produces a dead polymer from a growing chain depends on the nature of the reactive intermediate. These intermediates may be free radicals, anions, or cations. We shall devote most of this chapter to a discussion of the free-radical mechanism, since it readily lends itself to a very general treatment. The discussion of ionic intermediates is not as easily generalized. 

It is apparent from these reactions how chain transfer lowers the molecular weight of a chain-growth polymer. The effect of chain transfer on the rate of polymerization depends on the rate at which the new radicals reinitiate polymerization ... 

In order for a soHd to bum it must be volatilized, because combustion is almost exclusively a gas-phase phenomenon. In the case of a polymer, this means that decomposition must occur. The decomposition begins in the soHd phase and may continue in the Hquid (melt) and gas phases. Decomposition produces low molecular weight chemical compounds that eventually enter the gas phase. Heat from combustion causes further decomposition and volatilization and, therefore, further combustion. Thus the burning of a soHd is like a chain reaction. For a compound to function as a flame retardant it must intermpt this cycle in some way. There are several mechanistic descriptions by which flame retardants modify flammabiUty. Each flame retardant actually functions by a combination of mechanisms. For example, metal hydroxides such as Al(OH)2 decompose endothermically (thermal quenching) to give water (inert gas dilution). In addition, in cases where up to 60 wt % of Al(OH)2 may be used, such as in polyolefins, the physical dilution effect cannot be ignored. 

As the length and frequency of branches increase, they may ultimately reach from chain to chain. If all the chains are coimected together, a cross-linked or network polymer is formed. Cross-links may be built in during the polymerisation reaction by incorporation of sufficient tri- or higher functional monomers, or may be created chemically or by radiation between previously formed linear or branched molecules (curing or vulcanisation). Eor example, a Hquid epoxy (Table 1) oligomer (low molecular weight polymer) with a 6-8 is cured to a cross-linked soHd by reaction of the hydroxyl and... 

Often the substitution of fluorine atoms for hydrogen atoms in a polymer chain markedly increases the thermal stabiUty of the base polymer this is tme for polyimides. A typical fluorinated polyimide is prepared from the reaction of 2,2-bis(3,4-dicarboxyphenyl)hexafluoropropane dianhydride and 2,2-bis-(4-amino phenyl)hexafluoropropane according to the following reaction (36) ... 

A polymer molecule may have just a linear chain or one or more hranches protruding from the polymer hackhone. Branching results mainly from chain transfer reactions (see Chain Transfer Reactions later in this chapter) and affects the polymer s physical and mechanical properties. Branched polyethylene usually has a few long hranches and many more short hranches... 

Thermal stability is largely concerned with chemical reactivity which may involve oxygen, u.v. radiation or depolymerisation reactions. The presence of weak links and the possibility of chain reactions involving polymer chains may lead to polymers having lower thermal stability than predicted from studies of low molecular weight analogues. 

The multifunctional initiators may be di- and tri-, azo- or peroxy-compounds of defined structure (c.g. 20256) or they may be polymeric azo- or peroxy-compounds where the radical generating functions may be present as side chains 57 or as part of the polymer backbone."58"261 Thus, amphiphilic block copolymers were synthesized using the polymeric initiator 21 formed from the reaction between an a,to-diol and AIBN (Scheme 7.22).26 Some further examples of multifunctional initiators were mentioned in Section 3.3.3.2. It is also possible to produce less well-defined multifunctional initiators containing peroxide functionality from a polymer substrate by autoxidalion or by ozonolysis.-0... 

However, Pacansky and his coworkers77 studied the degradation of poly(2-methyl-l-pentene sulfone) by electron beams and from infrared studies of the products suggest another mechanism. They claim that S02 was exclusively produced at low doses with no concomitant formation of the olefin. The residual polymer was considered to be essentially pure poly(2-methyl-l-pentene) and this polyolefin underwent depolymerization after further irradiation. However, the high yield of S02 requires the assumption of a chain reaction and it is difficult to think of a chain reaction which will form S02 and no olefin. 

---