Polymers cross-linking agents

Polymer Cross-linking agent Comonomer Percentage of cross-linking (%) Inner surface area (m /g) Splitting percentage (%) Swellability Separation factor (a)... 

Polymer Cross-linking Agent Stretch Temperature, °C Stretch Ratio Tensile Strength, MPa Break Elongation, % Young s Modulus of Elasticity, MPa... 

Fig. 24. Representative cross-linking systems employed in negative tone CA resists, (a) Epoxy polymers requiring organic solvent development, (b) PHOST-based cross-linking systems requiring aqueous development, (c) Monomeric cross-linking agents used in PHOST matrix polymers.

Anaerobic stmctural adhesives are typically formulated from acryhc monomers such as methyl methacrylate [80-62-6] C Hg02, and methacrylic acid [79-41-4] (see Acrylic ester polymers). Very often, cross-linking agents such as dimethacrylates are also added. A peroxide, such as cumene... 

Fig. 15. Schematic of the interfacial polymerization process. The microporous film is first impregnated with an aqueous amine solution. The film is then treated with a multivalent cross-linking agent dissolved in a water-immiscible organic fluid, such as hexane or Freon-113. An extremely thin polymer film...

Polymers. AH nitro alcohols are sources of formaldehyde for cross-linking in polymers of urea, melamine, phenols, resorcinol, etc (see Amino RESINS AND PLASTICS). Nitrodiols and 2-hydroxymethyl-2-nitro-l,3-propanediol can be used as polyols to form polyester or polyurethane products (see Polyesters Urethane polymers). 2-Methyl-2-nitro-l-propanol is used in tires to promote the adhesion of mbber to tire cord (qv). Nitro alcohols are used as hardening agents in photographic processes, and 2-hydroxymethyl-2-nitro-l,3-propanediol is a cross-linking agent for starch adhesives, polyamides, urea resins, or wool, and in tanning operations (17—25). Wrinkle-resistant fabric with reduced free formaldehyde content is obtained by treatment with... 

An excellent review of composite RO and nanofiltration (NE) membranes is available (8). These thin-fHm, composite membranes consist of a thin polymer barrier layer formed on one or more porous support layers, which is almost always a different polymer from the surface layer. The surface layer determines the flux and separation characteristics of the membrane. The porous backing serves only as a support for the barrier layer and so has almost no effect on membrane transport properties. The barrier layer is extremely thin, thus allowing high water fluxes. The most important thin-fHm composite membranes are made by interfacial polymerization, a process in which a highly porous membrane, usually polysulfone, is coated with an aqueous solution of a polymer or monomer and then reacts with a cross-linking agent in a water-kniniscible solvent. 

Multifunctional Hydroxy, Mercapto, and Amino Compounds. These are used to cross-link halogenated polymers. Depending on the labihty of the halogen, the cross-linking agents can be capped to reduce reactivity or used in combination with accelerators to increase the rate of reaction. Benzoyl capping is common with hydroxy and mercapto compounds forming the carbamate by reaction with one equivalent of carbon dioxide is used with diamines. 

Sufficient titanate leads to a fully hardened polymer. Using only enough titanate to react with free hydroxyls, the resin may subsequently be cured at lower cost with conventional cross-linking agents. The titanated epoxy resin has a low power factor, which is important in electrical appHcations, eg, potting components and insulation (see Embedding). Titanates improve adhesion of metals to epoxies. 

Nail hardeners have been based on various proteia cross-linking agents. Only formaldehyde is widely used commercially. Contact with skin and inhalation must be avoided to preclude sensiti2ation and other adverse reactions. The popularity of products of this type is decreasiag because the polymers used ia nail elongators can be used to coat nails to iacrease the mechanical strength. 

The Nitro-dur system, marketed by Key Pharmaceuticals, Inc., contains nitroglycerin in acryUc-based polymeric adhesives with a cross-linking agent for polymer stabiUty. This depot of dmg provides a continuous source of active ingredient. An impermeable backing prevents release of nitroglycerin away from the skin. The systems are individually sealed in a paper polyethylene-foil pouch (81). 

---