Polymerised Phosphinates

Polymerised phosphines are frequently made by placing side groups on pre-formed polymers. Such derivatives can form metal-phosphine complexes which are of importance as catalysts [22]. Metal poly-yne polymers with phosphine side groups are known (8.163). 

Polymerised phosphine oxides are generally much more stable than polymerised phosphines. A high-molecular-weight polymer can be obtained from diphenyl(vinyl)phosphine oxide using either free radical or anionic initiation (12.176). 

Reaction of adsorbed inhibitors In some cases, the adsorbed corrosion inhibitor may react, usually by electro-chemical reduction, to form a product which may also be inhibitive. Inhibition due to the added substance has been termed primary inhibition and that due to the reaction product secondary inhibition " . In such cases, the inhibitive efficiency may increase or decrease with time according to whether the secondary inhibition is more or less effective than the primary inhibition. Some examples of inhibitors which react to give secondary inhibition are the following. Sulphoxides can be reduced to sulphides, which are more efficient inhibitorsQuaternary phosphonium and arsonium compounds can be reduced to the corresponding phosphine or arsine compounds, with little change in inhibitive efficiency . Acetylene compounds can undergo reduction followed by polymerisation to form a multimolecular protective film . Thioureas can be reduced to produce HS ions, which may act as stimulators of... 

Third generation initiators are based on the NHC system of second generation initiators, but do not contain any phosphine ligand. Instead, one or two pyridine ligands are weakly bound to the ruthenium centre (c/. Fig. 3.28, complexes 73 and 74c). Pyridine dissociates very easily and hardly competes with the olefin for the coordination site. As a result, complete initiation and fast propagation are enabled, therefore living polymerisation is rendered possible. 

Fig. 4.15), are active for ATRP of both styrene and methylmethacrylate (MMA) [46]. Polymerisation was well controlled with polydispersities ranging from 1.05 to 1.47. The rates of polymerisation 1 x 10 s ) showed the complexes to be more active than phosphine and amine ligated Fe complexes, and were said to rival Cu-based ATRP systems. It was quite recent that Cu(I) complexes of NHCs were tested as ATRP catalysts [47]. In this work, tetrahydropyrimidine-based carbenes were employed to yield mono-carbene and di-carbene complexes 42 and 43 (Fig. 4.15), which were tested for MMA polymerisation. The mono-carbene complex 42 gave relatively high polydispersities (1.4-1.8) and a low initiation efficiency (0.5), both indicative of poor catalyst control. The di-carbene complex 43 led to nncontrolled radical polymerisation, which was ascribed to the insolubility of the complex. 

Catalytic forms of copper, mercury and silver acetylides, supported on alumina, carbon or silica and used for polymerisation of alkanes, are relatively stable [3], In contact with acetylene, silver and mercury salts will also give explosive acetylides, the mercury derivatives being complex [4], Many of the metal acetylides react violently with oxidants. Impact sensitivities of the dry copper derivatives of acetylene, buten-3-yne and l,3-hexadien-5-yne were determined as 2.4, 2.4 and 4.0 kg m, respectively. The copper derivative of a polyacetylene mixture generated by low-temperature polymerisation of acetylene detonated under 1.2 kg m impact. Sensitivities were much lower for the moist compounds [5], Explosive copper and silver derivatives give non-explosive complexes with trimethyl-, tributyl- or triphenyl-phosphine [6], Formation of silver acetylide on silver-containing solders needs higher acetylene and ammonia concentrations than for formation of copper acetylide. Acetylides are always formed on brass and copper or on silver-containing solders in an atmosphere of acetylene derived from calcium carbide (and which contains traces of phosphine). Silver acetylide is a more efficient explosion initiator than copper acetylide [7],... 

Dispersed phase polymerisation of HIPEs has also been used to prepare polymer-supported quaternary onium phase transfer catalysts [162]. One strategy involved the polymerisation of a concentrated emulsion of vinyl benzyl chloride (VBC) in water and subsequent quaternisation of the polymer resin with tertiary amines and phosphines (Fig. 22). 

On the basis of this report, in 2003, Gagne and collaborators described an imprinting system involving the use of the crown ether to improve Cammidge s system [48]. The polymer was prepared by imprinting the polymerisable bis-triphenyl-phosphine-Pd(catecolate) together with a polymerisable 1 1 complex formed by the 4 -vinylbenzo-18-crown-6 ether and n-butylamine (72). 

Palladium catalysts with simple monodentate phosphine ligands (e.g. PPh3) can catalyze the methoxycarbonylation of ethylene. However, the Lucite process employs a bulky diphosphine, 1,2-( Bu2PCH2)2CgH4, and is highly active and selective under quite mild conditions (10 bar/80°C). Two alternative catalytic cycles are possible, based either upon a palladium hydride or a palladium methoxide complex (Figure 9), and mechanistic and spectroscopic studies indicate that the hydride cycle is dominant. The alkene and CO insertion steps are the same as those in the Pd-catalyzed co-polymerisation of CO and alkenes to polyketones (Section 4.4). 

Figure 29 In situ P H HPNMR spectra (phosphine region) of the co-polymerisation of CO with styrene catalysed by Rh-BINAPHOS (a) in a zirconiaNMR tube, recorded at 202.5 MHz (b) in a bubble column reactor, recorded at 81.0 MHz. Note only the alkyl intermediate 2 is observed in the unmixed HPNMR tube due to inefficient mass transfer of CO into solution. In the bubble column, delivery of CO to the catalyst is efficient, and so the acyl intermediate 1 is also observed ...

---