Polybutadiene copolymers, liquid rubbers

Abbreviations coiX-V] = copolymers of X and Y colX-b-Yl = block copolymers of poly X and poly Y ST = styrene MA = methyl acrylate MMA = methyl methacrylate AN = acrylonitrile BD = butadiene LR (liquid rubbers) = a, cj-polybutadiene-diols and -dicarboxylic acids Cell-Ac = cellulose acetate Cell-N02 = cellulose nitrate. 

Liquid polymers are useful as tackifiers for rubbers, 72) and acrylic coatings. The most interesting are hydroxytelechelic polybutadienes, especially liquid butadiene-acrylonitrile (85/15) copolymers (trademark CN-15, ARCO). This product, known since 1971 as a tackifier, has the following characteristics viscosity 493 poises at 30 °C, tv[n = 4400, hydroxyl number/chain = 2.5. The incorporation of 5% of CN-15 in ethylene-propylene rubber (EPT Nordel 1070) increases its tack considerably 173) close to that of natural rubber or butyl rubbers (Table 4.1). 

Natural Rubber and Synthetic Polyisoprene Polybutadiene and Its Copolymers Polyisobutylene and Its Copolymers Ethylene-Propylene Copolymers and Terpolymers Polychloroprene Silicone Elastomers Fluorocarbon Elastomers Fluorosilicone Elastomers Electron Beam Processing of Liquid Systems Grafting and Other Polymer Modifications... 

DMTA is a very interesting tool for characterizing heterogeneous materials in which domains of distinct Tg values coexist. The most interesting cases involve modified thermosets of different types (see Chapter 8). Examples are the use of rubbers (e.g., liquid polybutadiene and random copolymers), or thermoplastics (e.g., polyethersulphone or polyetherimide in epoxy matrices or poly(vinyl acetate) in unsaturated polyesters), as impact modifier (epoxies), or low-profile additives (polyesters). The modifier-rich phase may be characterized by the presence of a new a peak (Fig. 11.10). But on occasions there may be superposition of peaks and the presence of the modifier cannot be easily detected by these techniques. If part of the added polymer is soluble in the thermoset matrix, its eventual plasticizing effect can be determined from the corresponding matrix Tg depletion, and the... 

Transition metal catalyzed hydrogenation in ionic liquids has also been applied to the hydrogenation of polymers. First studies were presented by Dupont s group which investigated the hydrogenation of acrylonitrile-butadiene copolymers [102]. These early studies were later expanded by Rosso and coworkers studying the rhodium catalyzed hydrogenation of polybutadiene (PBD), nitrile-butadiene rubber (NBR) and styrene-butadiene rubber (SBR) in a [BMIM][BF4]/toluene and a... 

The photosensitive resin consists either of a liquid functionalised oligomer, usually with acrylate groups, or a reactive polymer which will be applied as hot melt. There are two main classes of reactive polymers acrylic hot melts which may contain a tackifying monomer, and thermoplastic rubbers which predominantly block copolymers with polybutadiene or polyisoprene chains [3]. A radical-type photoinitiator is always needed to produce, upon UV-exposure, the free radicals that will initiate the polymerisation or cross-linking process. 

Thin-layer liquid chromatography has been employed for the determination of alkylated cresols and amine antioxidants [102, 103] in polybutadiene, phenolic antioxidants in PE [104-106] and PP [106], dilauryl and distearyl thiodipropionate antioxidants in polyolefins, ethylene-vinyl acetate copolymer, acrylonitrile-styrene terpolymer and PS, UV absorbers and organotin stabilisers in polyolefins [102], and accelerators such as guanidines, thiazoles, thiurans, sulfenamides, diethiocarbamides, and morpholine disulfides in unvulcanised rubber compounds. 

Early results with cryomicrotomes were described by Cobbold and Mendelson [80]. Polyurethane elastomer, a blend of crystalline and noncrystalline polymers, showed spherulitic textures after sectioning at about -70°C. Injection molded polypropylene (PP) was also sectioned at about -70°C, while polytetrafluoroethylene (PTFE) was sectioned at much lower temperatures. The authors concluded that the technique, though difficult, had potential. Extruded styrene-butadiene-styrene (SBS) copolymer was prepared by cryosectioning with a diamond knife in liquid air at —85 to —115°C, followed by osmium tetroxide vapor staining for one hour [81]. This method revealed the alternating sequence of the polystyrene and polybutadiene lamellae. Odell et al. [82] prepared extruded triblock copolymer by first chemically hardening the polybutadiene, with osmium tetroxide, followed by cryoultramicrotomy to produce 30 nm thick sections which showed fine structure details. Parallel polystyrene rods were observed in the SBS copolymer. Ultramicrotomy and selective staining with osmium tetroxide was also used in the preparation of a binary blend of PP and thermoplastic rubber [83]. 

---