Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Plasticizers determination

ISO 527, Plastics Determination of Tensile Properties, ISO, Geneva, Swit2erland, 1991. [Pg.159]

ISO 178 International Standard Plastics — Determination of flexural properties of rigid plastics... [Pg.354]

When water is used as the immersion liquid, the test is essentially the ASTM Standard Test Method (D570) for Water Absorption of Plastics.( ) Determinations of the relative rate of water absorption are important in evaluating the effects of moisture exposure on such properties as mechanical strength, electrical resistivity, dielectric... [Pg.30]

FIGURE 26.6 ASTM plasticity determination for fine-grained soils. (Adapted from U.S. EPA, Requirements for Hazardous Waste Landfill Design, Construction, and Closure, EPA/625/4-89/022, U.S. Environmental Protection Agency, Cincinnati, OH, August 1989.)... [Pg.1104]

ISO 11357 2005 Plastics - Determination of the melt mass-flow rate (MFR) and the melt-volume flow rate (MVR) of thermoplastics. International Organization for Standardization, Geneva, Switzerland. [Pg.448]

For plastics, ISO 3451 Plastics — Determination of Ash describes various methods for determination of the ash content of different types of plastics including those containing glass fibres and/or flame-retardants. [Pg.588]

A development of plasticity determination by means of the Mooney viscometer. The same instrument is used but the temperature of operation is higher and the test is continued until the sample vulcanises. A curve of Mooney reading against time is drawn, from which the scorch and cure characteristics are estimated (BS 903-A58). [Pg.41]

DIN 53 405 Bestimmung der Wanderung von Weichmachern. ISO 177-1988 Plastics -Determination of migration of plasticizers. [Pg.115]

ISO 2578, Plastics - Determination of time-temperature limits after prolonged exposure to heat, 1993. [Pg.80]

ISO 182, Parts 1-4, Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures, 1990-1993. [Pg.80]

ISO 305, Plastics - Determination of thermal stability of poly(vinyl chloride), related chlorine-containing homopolymers and copolymers and their compounds - Discoloration method, 1990. [Pg.80]

ISO 176, Plastics - Determination of loss of plasticizers - Activated carbon method, 1976. [Pg.80]

ISO 4611, Plastics - Determination of the effects of exposure to damp heat, water spray and salt mist, 1987. [Pg.80]

ISO 4599, Plastics - Determination of resistance to environmental stress cracking (ESC) - Bent strip method, 1986. [Pg.80]

ISO 4582, Plastics - Determination of changes in colour and variations in properties after exposure to daylight under glass, natural weathering or laboratory light sources, 1998. [Pg.81]

ISO 899-1, Plastics - Determination of creep behaviour - Part 1 Tensile creep, 1993. [Pg.81]

ISO 527-4, Plastics - Determination of tensile properties - Part 4 Test conditions for isotropic and orthotropic fibre-reinforced plastic composites, 1997. [Pg.82]

ISO 179, Parts 1 2, Plastics - Determination of Charpy impact properties, 1997-2000. [Pg.93]

ISO 6721, Parts 1-10, Plastics - Determination of dynamic mechanical properties, 1994-2001. [Pg.93]

ISO 2556, Plastics - Determination of the gas transmission rate of films and thin sheets under atmospheric pressure - Manometric method, 1974. [Pg.94]


See other pages where Plasticizers determination is mentioned: [Pg.483]    [Pg.354]    [Pg.64]    [Pg.80]    [Pg.80]    [Pg.93]    [Pg.93]    [Pg.93]    [Pg.93]    [Pg.93]    [Pg.94]    [Pg.95]    [Pg.95]   
See also in sourсe #XX -- [ Pg.603 , Pg.604 , Pg.605 ]




SEARCH



ASTM Tests for Determination of Phenolic Antioxidants in Plastics

Determination of Plastic Properties

Determination of plasticizers in water

Difficulty determining plastic deformation

Methods to determine plastic response of films

Plastic properties determination

Plasticization effects, determination

Standard Practice for Plastics Dynamic Mechanical Properties Determination and Report of Procedures

Standard Test Method for Determining Ignition Temperature of Plastics

© 2024 chempedia.info