Of PEEK

Production of PEEK resia is less than 500 t/yr worldwide (106). Growth is expected to exceed 10%/yr. Because of chemical and manufacturiag constraints, the price, ca 55/kg for neat resia, is likely to remain high. 

Excellent toughness and wear resistance. For example, the resistance to cut through of wire coverings is far superior to that of most other heat-resisting plastics. It is interesting to note that in 1994, 50% of applications of PEEK were related to the excellent wear behaviour. 

Data are for fully crystalline material apart from electrical data for PEEKK It may be noted that the amorphous SG of PEEK is 1.265. The modulus data is flexural for PEEK and tensile for PEEKK. 

Example 3.4 For the PEEK/carbon fibre composite referred to in Example 3.2 calculate the values of V j and Vent if it is known that the ultimate tensile strength of PEEK is 62 MN/m. ... 

Figure 12-6I. Dresser-Rand HPS proprietary valve design, using proprietary blend of PEEK, an advanced non-metallic valve plate material, allowing for temperature ranges greater than previously available nonmetallic plate materials, for lubricated and nonlubri-cated applications for long life. (Used by permission Form 85084, 1992.

Industrial applications of PEEK take advantage of the outstanding thermal properties, and include use in high-performance automotive and aerospace components, and in printed circuit boards. 

Each section consists of a reaction plate where the reaction mixture flows, surrounded by two cooling plates containing the UE. The reactants and catalyst are stored separately and put into contact at the opening of the first reaction plate. The pilot holdup is typically 1.5 1. The successive plates of the reactor can be represented as shown in Figure 12.1. Inside the reactive plate (RP), the environment of the reaction mixture is composed of PEEK. The UE flows between two stainless steel plates, the sandwich plate (SP) and the transition plate (TP). 

Figure 8 Mass loss of poly(ether-ketone-carbaborane) relative to that of PEEK (dashed).

All required materials for a PSI system are easily accessible a flask with two ground glass joints (or one joint and an arm), rubber septum, rubber hose, a short length of PEEK tubing ( 0.5 m), a PEEK chromatography fitting (nut and ferrule) and a source of... 

The strong alkaline solvents need some special efforts concerning materials. Capillaries and fittings should be of PEEK. The injection valve must be designated to be alkali resistant (e.g., Tefzel rotors of Rheodyne valves). Storage bottles for mobile solvents have to be of plastics and should be supplemented with a tube filled with caustic soda pellets. 

Yencho then constructed the initial version of the machine and explored the parameters necessary to successfully form flaw-free parts. A key finding concerned the effects of trapped moisture. Despite the generally hydrophobic nature of PEEK, it was found that small amounts of moisture absorbed by the Gr/PEEK laminates subsequent to their manufacture converted into steam during the forming operation and caused extensive delamination. This was in... 

The components within the F1PLC system are interconnected by short segments of transfer tubing with a very small internal diameter (0.1mm). Traditionally constructed from stainless steel, transfer tubes can also be made of PEEK a (polyetheretherketone), a coloured, flexible polymer that is less expensive to fabricate than stainless steel and is resistant to common solvents under elevated pressures (up to 350 bar). 

An interface or housing for micro fluidic applications was designed and fabricated. The device, made of PEEK, allows facile non-permanent coupling of standard capillary tubing to silicon/glass micro mixer chips. No additional adhesive material was used to for a secure and tight interconnect [70],... 

Yoon TH, McGrath JE (1991) Effect of surface preparation and thermoplastic ahesive structure on the adhesion behavior of peek-graphite composites. Mater Res Soc Symp Proc 190 (Plasma Process Synth Mater) 3 137-142... 

The use of ICP-MS provides some important benefits when coupled to an HPLC that separates As species prior to measurement. ICP-MS has fit-for-purpose limits of detection (LoDs) thus, analytical, not preparative, separation systems can be used with a high sampling rate ( 1 ms) in order to measure transient signals and to separately quantify closely eluting compounds from HPLC. HPLC-ICP-MS coupling can be achieved simply via a 50 cm piece of PEEK tubing without loss of peak resolution, whereas chromatographic flow rates are compatible with conventional ICP-MS spray chambers. 

Synthesis and Properties of PEEK/Carbon Nano tube Nanocomposites... 

---