Molten ceramics

The type of attack that occurs in liquid media is highly dependent on the chemical nature of the liquid—that is, molten metal, molten ceramic, or aqueous solution. We will consider two industrially important cases attack by molten metals and attack by aqueous media. The attack of most metal oxide ceramics by molten metals involves a simple exchange of one metal ion for another. For example, silicon dioxide in contact with molten aluminum is susceptible to the following corrosion reaction ... 

Raman spectroscopy was used to investigate molten ceramic oxide materials formed in the Ca0-Al203 system.122 Raman spectroscopy showed... 

The easiest way to define surface energy is to start with a liquid (it could, for example, be a molten ceramic) and imagine that it is suspended in a wire frame. One bar of the frame is movable and allows us to increase the surface area by an amount dA. The force that we have to apply must be sufficient to overcome the opposing surface tension, y. The work done, dw, in increasing the surface area is... 

Figure 15.9 shows that molten ceramics are considerably more viscous than molten metals, resulting in low rates of infiltration. 

Molten alkah metal monofluorophosphates are reactive and corrosive, hydrolyzing to generate HF and reacting with many metals and ceramics. 

Molten Carbonate Fuel Cell. The electrolyte ia the MCFC is usually a combiaation of alkah (Li, Na, K) carbonates retaiaed ia a ceramic matrix of LiA102 particles. The fuel cell operates at 600 to 700°C where the alkah carbonates form a highly conductive molten salt and carbonate ions provide ionic conduction. At the operating temperatures ia MCFCs, Ni-based materials containing chromium (anode) and nickel oxide (cathode) can function as electrode materials, and noble metals are not required. 

Fused Salt Electrolysis. Only light RE metals (La to Nd) can be produced by molten salt electrolysis because these have a relatively low melting point compared to those of medium and heavy RE metals. Deposition of an alloy with another metal, Zn for example, is an alternative. The feed is a mixture of anhydrous RE chlorides and fluorides. The materials from which the electrolysis cell is constmcted are of great importance because of the high reactivity of the rare-earth metals. Molybdenum, tungsten, tantalum, or alternatively iron with ceramic or graphite linings are used as cmcible materials. Carbon is frequently used as an anode material. 

Alternatively, tows of fibers can be passed through a Hquid metal bath, where the individual fibers are wet by the molten metal, wiped of excess metal, and a composite wine is produced. A bundle of such wines can be consoHdated by extmsion to make a composite. Another pressureless Hquid metal infiltration process of making MMCs is the Prim ex process (Lanxide), which can be used with certain reactive metal alloys such as Al—Mg to iafiltrate ceramic preforms. For an Al—Mg alloy, the process takes place between 750—1000°C ia a nitrogen-rich atmosphere (2). Typical infiltration rates are less than 25 cm/h. 

Fused-salt electrolysis of K2NbFy is not an economically feasible process because of the low current efficiency (31). However, electrowinning has been used to obtain niobium from molten alkaU haUde electrolytes (32). The oxide is dissolved in molten alkaU haUde and is deposited in a molten metal cathode, either cadmium or zinc. The reaction is carried out in a ceramic or glass container using a carbon anode the niobium alloys with the cathode metal, from which it is freed by vacuum distillation, and the niobium powder is left behind. 

The molten filaments are extmded through the spinnerette down a vertical chimney where they are air-quenched. The filaments are then converged to form the threadline in the V shape formed by crossed ceramic pins or other similar devices. The threadline passes to the floor below where finish is appHed and is wound up on the spin bobbins. 

Refractories are materials that resist the action of hot environments by containing heat energy and hot or molten materials (1). There is no weU-estabhshed line of demarcation between those materials that are and those that are not refractory. The abiUty to withstand temperatures above 1100°C without softening has, however, been cited as a practical requirement of industrial refractory materials (see Ceramics). The type of refractories used in any particular apphcation depends on the critical requirements of the process. For example, processes that demand resistance to gaseous orHquid corrosion require low permeabihty, high physical strength, and abrasion resistance. Conditions that demand low thermal conductivity may require entirely different refractories. Combinations of several refractories are generally employed. 

In any brazing/soldering process, a molten alloy comes in contact with a surface of solid, which may be an alloy, a ceramic, or a composite material (see Ceramics Composite materials). For a molten alloy to advance over the soHd surface a special relationship has to exist between surface energies of the hquid—gas, soHd—gas, and Hquid—soHd interfaces. The same relationships should, in principle, hold in joining processes where a molten alloy has to fill the gaps existing between surfaces of the parts to be joined. In general, the molten alloy should have a lower surface tension than that of the base material. 

Development of practical and low cost separators has been an active area of ceU development. CeU separators must be compatible with molten lithium, restricting the choice to ceramic materials. Early work employed boron nitride [10043-11-5] BN, but a more desirable separator has been developed using magnesium oxide [1309-48-4], MgO, or a composite ofMgO powder—BN fibers. Corrosion studies have shown that low carbon steel or... 

---