Modification probes

Rees DG, Hailing PJ (2001) Chemical modification probes accessibility to organic phase proteins on surfaces are more exposed than in lyophilized powders. Enzyme Microb Technol 28 282-292... 

Liu, B., Ma, M. Y, Zacher, D., Betard, A., Yusenko, K., Metzler-Nolte, N., Woll, C., and Fischer, R. A. Chemistry of SURMOFs Layer-selective installation of fimctional groups and postsynthetic covalent modification probed by fluorescence microscopy. J Am Chem Soc 133, 1734-1737 (2011). 

The dynamics of polymers at surfaces can be studied via dynamic light scattering (DLS), as described in Section IV-3C. A modification of surface DLS using an evanescent wave to probe the solution in a region near the interface has... 

Surfaces are investigated with surface-sensitive teclmiques in order to elucidate fiindamental infonnation. The approach most often used is to employ a variety of techniques to investigate a particular materials system. As each teclmique provides only a limited amount of infonnation, results from many teclmiques must be correlated in order to obtain a comprehensive understanding of surface properties. In section A 1.7.5. methods for the experimental analysis of surfaces in vacuum are outlined. Note that the interactions of various kinds of particles with surfaces are a critical component of these teclmiques. In addition, one of the more mteresting aspects of surface science is to use the tools available, such as electron, ion or laser beams, or even the tip of a scaiming probe instrument, to modify a surface at the atomic scale. The physics of the interactions of particles with surfaces and the kinds of modifications that can be made to surfaces are an integral part of this section. 

Some recent advances in stimulated desorption were made with the use of femtosecond lasers. For example, it was shown by using a femtosecond laser to initiate the desorption of CO from Cu while probing the surface with SHG, that the entire process is completed in less than 325 fs [90]. The mechanism for this kind of laser-induced desorption has been temied desorption induced by multiple electronic transitions (DIMET) [91]. Note that the mechanism must involve a multiphoton process, as a single photon at the laser frequency has insufScient energy to directly induce desorption. DIMET is a modification of the MGR mechanism in which each photon excites the adsorbate to a higher vibrational level, until a suflBcient amount of vibrational energy has been amassed so that the particle can escape the surface. 

Staufer U 1995 Surface modification with a scanning proximity probe microscope Scanning Tunnelling Microscopy II ed R Wiesendanger and Fl-J Guntherodt (Beriin Springer) ch 8... 

Characterization of zeolites is primarily carried out to assess tire quality of materials obtained from syntliesis and postsyntlietic modifications. Secondly, it facilitates tire understanding of tire relation between physical and chemical properties of zeolites and tlieir behaviour in certain applications. For tliis task, especially, in situ characterization metliods have become increasingly more important, tliat is, techniques which probe tire zeolite under actual process conditions. 

Venus probe. References should be consulted for the details of the optical transparency of the different type diamonds (9,14,16—19). The direct band gap for diamond is 5.47 eV. Natural diamond exhibits many colors, and color modification by irradiation and annealing is common (36). Though cubic, most natural diamonds show strain birefringence under crossed polaroids. 

Two-dimensional C//correlations such as C//COSY or HC HMQC and HSQC provide the Jqh connectivities, and thereby apply only to those C atoms which are linked to H and not to non-protonated C atoms. Modifications of these techniques, also applicable to quaternary C atoms, are those which are adjusted to the smaller Jqh and Jqh couplings (2-25 Hz, Tables 2.8 and 2.9) Experiments that probe these couplings include the CH COLOC (correlation via long range couplings) with carbon-13 detection (Fig. 2.16) and HC HMBC (heteronuclear multiple bond coherence) with the much more sensitive proton detection (Fig. 2.17)... 

Concluding this section, two interesting variants of the STM should be addressed. The spin-polarized STM (SPSTM), which works with a ferromagnetic tip, can be used to probe surface magnetism with high resolution [5.47, 5.48]. Other modifications of the STM involve electromagnetic radiation, whereby two basic concepts can... 

Anemotherm - The Anemotherm, a hot wire anemometer, has been extensively applied to flare gas measurement and has been successfully used after modifications to reduce probe fouling. A technique used to reduce fouling is the installation of a steam coil around the tip of the probe, to prevent gases from condensing on the probe. 

Sample surfaces are atomically smooth surfaces of cleaved mica sheets for SFA, and various colloidal spheres and plates for a colloidal probe AFM. These surfaces can be modified using various chemical modification techniques, such as Langmuir-Blodged (LB) deposition [12,19] and silanization reactions [20,21]. For more detailed information, see the original papers and references texts. 

Zinc sulfide, with its wide band gap of 3.66 eV, has been considered as an excellent electroluminescent (EL) material. The electroluminescence of ZnS has been used as a probe for unraveling the energetics at the ZnS/electrolyte interface and for possible application to display devices. Fan and Bard [127] examined the effect of temperature on EL of Al-doped self-activated ZnS single crystals in a persulfate-butyronitrile solution, as well as the time-resolved photoluminescence (PL) of the compound. Further [128], they investigated the PL and EL from single-crystal Mn-doped ZnS (ZnS Mn) centered at 580 nm. The PL was quenched by surface modification with U-treated poly(vinylferrocene). The effect of pH and temperature on the EL of ZnS Mn in aqueous and butyronitrile solutions upon reduction of per-oxydisulfate ion was also studied. EL of polycrystalline chemical vapor deposited (CVD) ZnS doped with Al, Cu-Al, and Mn was also observed with peaks at 430, 475, and 565 nm, respectively. High EL efficiency, comparable to that of singlecrystal ZnS, was found for the doped CVD polycrystalline ZnS. In all cases, the EL efficiency was about 0.2-0.3%. 

---