Mixing micromixing

The composition PDF thus evolves by convective transport in real space due to the mean velocity (macromixing), by convective transport in real space due to the scalar-conditioned velocity fluctuations (mesomixing), and by transport in composition space due to molecular mixing (micromixing) and chemical reactions. Note that any of the molecular mixing models to be discussed in Section 6.6 can be used to close the micromixing term. The chemical source term is closed thus, only the mesomixing term requires a new model. 

Wong S, Ward M, Wharton C (2004) Micro T-mixer as a rapid mixing micromixer. Sens Actuators B Chem 100(3) 359-379... 

Macromixing vs Micromixing. Mixing in an agitated tank is considered to occur at two levels, macromixing and micromixing. 

Macromixing is estabflshed by the mean convective flow pattern. The flow is divided into different circulation loops or zones created by the mean flow field. The material is exchanged between zones, increasing homogeneity. Micromixing, on the other hand, occurs by turbulent diffusion. Each circulation zone is further divided into a series of back-mixed or plug flow cells between which complete intermingling of molecules takes place. 

Micromixing Mixing among molecules of different ages (i.e., mixing between macrofluid clumps). Mixing on a scale smaller tlian tlie minimum eddy size or minimum striation diickness by molecular diffusion. 

In what follows, both macromixing and micromixing models will be introduced and a compartmental mixing model, the segregated feed model (SFM), will be discussed in detail. It will be used in Chapter 8 to model the influence of the hydrodynamics on a meso- and microscale on continuous and semibatch precipitation where using CFD, diffusive and convective mixing parameters in the reactor are determined. 

In the SFM the reactor is divided into three zones two feed zones fj and (2 and the bulk b (Figure 8.1). The feed zones exchange mass with each other and with the bulk as depicted with the flow rates mi 2, i,3 and 2,3 respectively, according to the time constants characteristic for micromixing and mesomix-ing. As imperfect mixing leads to gradients of the concentrations in the reactor, different supersaturation levels in different compartments govern the precipitation rates, especially the rapid nucleation process. 

The failure of conventional criteria may be due to the fact that it is not only one mixing process which can be limiting, rather for example an interplay of micromixing and mesomixing can influence the kinetic rates. Thus, by scaling up with constant micromixing times on different scales, the mesomixing times cannot be kept constant but will differ, and consequently the precipitation rates (e.g. nucleation rates) will tend to deviate with scale-up. 

The conventional scale-up criteria scale-up with constant stirrer speed , scale-up with constant tip speed and scale-up with constant specific energy input are all based on the assumption that only one mixing process is limiting. If, for example, the specific energy input is kept constant with scale-up, the same micromixing behaviour could be expected on different scales. The mesomixing time, however, will change with scale-up as a result, the kinetic rates and particle properties will be different and scale-up will fail. 

In order to account for both micromixing and mesomixing effects, a mixing model for precipitation based on the SFM has been developed and applied to continuous and semibatch precipitation. Establishing a network of ideally macromixed reactors if macromixing plays a dominant role can extend the model. The methodology of how to scale up a precipitation process is depicted in Figure 8.8. 

The reactor has been successfully used in the case of forced precipitation of copper and calcium oxalates (Jongen etal., 1996 Vacassy etal., 1998 Donnet etal., 1999), calcium carbonate (Vacassy etal., 1998) and mixed yttrium-barium oxalates (Jongen etal., 1999). This process is also well adapted for studying the effects of the mixing conditions on the chemical selectivity in precipitation (Donnet etal., 2000). When using forced precipitation, the mixing step is of key importance (Schenk etal., 2001), since it affects the initial supersaturation level and hence the nucleation kinetics. A typical micromixer is shown in Figure 8.35. 

Baldyga, J. and Bourne, J.R., 1984b. A fluid mechanical approach to turbulent mixing and chemical reaction. Part II Micromixing in the light of turbulence theory. Chemical Engineering Communications, 28, 243-258. 

Garside, J. and Tavare, N.S., 1985. Mixing, reaction and precipitation limits of micromixing in an MSMPR crystallizer. Chemical Engineering Science, 40, 1485-1493. 

FIGURE 15.14 Macromixing versus micromixing—a schematic representation of mixing space. 

---