Methyl methacrylate constants

Combination and disproportionation are competitive processes and do not occur to the same extent for all polymers. For example, at 60°C termination is virtually 100% by combination for polyacrylonitrile and 100% by disproportionation for poly (vinyl acetate). For polystyrene and poly (methyl methacrylate), both reactions contribute to termination, although each in different proportions. Each of the rate constants for termination individually follows the Arrhenius equation, so the relative amounts of termination by the two modes is given by... 

Figure 6.3 shows some data which constitute a test of Eq. (6.26). In Fig. 6.3a, Rp and [M] are plotted on a log-log scale for a constant level of redox initiator. The slope of this line, which indicates the order of the polymerization with respect to monomer, is unity, showing that the polymerization of methyl methacrylate is first order in monomer. Figure 6.3b is a similar plot of the initial rate of polymerization—which essentially maintains the monomer at constant con-centration—versus initiator concentration for several different monomer-initiator combinations. Each of the lines has a slope of indicating a half-order dependence on [I] as predicted by Eq. (6.26).

Figure 6.3 Log-log plots of Rp versus concentration which verify the order of the kinetics with respect to the constituent varied, (a) Monomer (methyl methacrylate) concentration varied at constant initiator concentration. [Data from T. Sugimura and Y. Minoura, J. Polym. Sci. A-l 2735 (1966).] (b) Initiator concentration varied AIBN in methy methacrylate (o), benzoyl peroxide in styrene ( ), and benzoyl peroxide in methyl methacrylate ( ). (From P. J. Flory, Principles of Polymer Chemistry, copyright 1953 by Cornell University, used with permission.)...

Chain transfer to solvent is an important factor in controlling the molecular weight of polymers prepared by this method. The chain-transfer constants for poly(methyl methacrylate) in various common solvents (C) and for various chain-transfer agents are Hsted in Table 10. 

Table 10. Chain-Transfer Constants for Methyl Methacrylate...

Poly(methyl methacrylate) is a good electrical insulator for low-frequency work, but is inferior to such polymers as polyethylene and polystyrene, particularly at high frequencies. The influence of temperature and frequency on the dielectric constant is shown in Figure 15.9. 

Which mechanism of termination will be preferably applied depends largely on the monomer used. Thus, methyl methacrylate chains terminate to a large extent by disproportionation, whereas styrene chains tend to termination by combination. The ratios of termination rate constants 8 = ktJkic (for disproportionation, td, combination,, c) are 5 == 0 and 5 = 2 for styrene [95] and methyl methacrylate [96], respectively. In the case of styrene, however, the values of 8 reported in the literature are at variance. Berger and Meyerhoff [97] found 8 = 0.2, at 52°C. Therefore, it is possible that a fraction of styrene terminates by disproportionation. 

Waters61 have measured relative rates of p-toluenesulfonyl radical addition to substituted styrenes, deducing from the value of p + = — 0.50 in the Hammett plot that the sulfonyl radical has an electrophilic character (equation 21). Further indications that sulfonyl radicals are strongly electrophilic have been obtained by Takahara and coworkers62, who measured relative reactivities for the addition reactions of benzenesulfonyl radicals to various vinyl monomers and plotted rate constants versus Hammett s Alfrey-Price s e values these relative rates are spread over a wide range, for example, acrylonitrile (0.006), methyl methacrylate (0.08), styrene (1.00) and a-methylstyrene (3.21). The relative rates for the addition reaction of p-methylstyrene to styrene towards methane- and p-substituted benzenesulfonyl radicals are almost the same in accord with their type structure discussed earlier in this chapter. 

Fig. 2. Arrhenius plots of the rate constants of the anionic polymerization of methyl methacrylate in THF as the solvent and with Na+ orCs+ as the counterion. (R. Kraft, A. H. E. Muller, V. Warzelhan, H. Hocker, G. V. Schulz, Ref.35>)...

Additional data were obtained from the study of kinetics of the slow disproportionation of the living dimers of methyl methacrylate. The progress of this reaction is shown in Fig. 8 which displays also the respective rates and equilibrium constants. 

The Diels-Alder reaction of methyl methacrylate with cyclopentadiene was studied [72] with solutions from three different regions of the pseudophase diagram for toluene, water and 2-propanol, in the absence and in the presence of surfactant [sodium dodecyl sulfate (SDS) and hexadecyltrimethylammonium bromide (HTAB)]. The composition of the three solutions (Table 6.11) corresponds to a W/O-fiE (A), a solution of small aggregates (B) and a normal ternary solution (C). The diastereoselectivity was practically constant in the absence and in the presence of surfactant a slight increase of endo adduct was observed in the C medium in the presence of surfactant. This suggests that the reaction probably occurs in the interphase and that the transition state has a similar environment in all three media. 

The above explanation of autoacceleration phenomena is supported by the manifold increase in the initial polymerization rate for methyl methacrylate which may be brought about by the addition of poly-(methyl methacrylate) or other polymers to the monomer.It finds further support in the suppression, or virtual elimination, of autoacceleration which has been observed when the molecular weight of the polymer is reduced by incorporating a chain transfer agent (see Sec. 2f), such as butyl mercaptan, with the monomer.Not only are the much shorter radical chains intrinsically more mobile, but the lower molecular weight of the polymer formed results in a viscosity at a given conversion which is lower by as much as several orders of magnitude. Both factors facilitate diffusion of the active centers and, hence, tend to eliminate the autoacceleration. Final and conclusive proof of the correctness of this explanation comes from measurements of the absolute values of individual rate constants (see p. 160), which show that the termination constant does indeed decrease a hundredfold or more in the autoacceleration phase of the polymerization, whereas kp remains constant within experimental error. 

The results of chain transfer studies with different polymer radicals are compared in Table XIV. Chain transfer constants with hydrocarbon solvents are consistently a little greater for methyl methacrylate radicals than for styrene radicals. The methyl methacrylate chain radical is far less effective in the removal of chlorine from chlorinated solvents, however. Vinyl acetate chains are much more susceptible to chain transfer than are either of the other two polymer radicals. As will appear later, the propagation constants kp for styrene, methyl methacrylate, and vinyl acetate are in the approximate ratio 1 2 20. It follows from the transfer constants with toluene, that the rate constants ktr,s for the removal of benzylic hydrogen by the respective chain radicals are in the ratio 1 3.5 6000. Chain transfer studies offer a convenient means for comparing radical reactivities, provided the absolute propagation constants also are known. 

In thermal polymerization where the rate of initiation may also vary with composition, an abnormal cross initiation rate may introduce a further contribution to nonadditive behavior. The only system investigated quantitatively is styrene-methyl methacrylate, rates of thermal copolymerization of which were measured by Walling. The rate ratios appearing in Eq. (26) are known for this system from studies on the individual monomers, from copolymer composition studies, and from the copolymerization rate at fixed initiation rate. Hence a single measurement of the thermal copolymerization rate yields a value for Ri. Knowing hm and ki22 from the thermal initiation rates for either monomer alone (Chap. IV), the bimolecular cross initiation rate constant kii2 may be calculated. At 60°C it was found to be 2.8 times that... 

Very similar variations in average copolymer composition with conversion have recently been observed in the styrene methyl methacrylate system by both Johnson et al ( and by Dionisio and O Driscoll (. The reason for the variation may be due to a viscosity effect on propagation rate constants QO). 

Table I. Observed Sn- C Coupling Constants in Poly(Tri-n-butyltin Methacrylate/Methyl Methacrylate)in Various Solvents a...

Methyl methacrylate (MMA), 16 227 Alfrey-Price parameters, 7 617t azeotropic mixtures with, 16 236t block copolymer synthesis, 7 647t C-2 routes to, 16 252-254 C-3 routes to, 16 246—252 C-4 routes to, 16 254—257 carbon monoxide in production of, 5 6 chain-transfer constants for, 16 284t comonomer with acrylonitrile, 1 451t cumene as feedstock, 8 156 in flame-retardant resin formulation,... 

---