Melting creep

Sato et al. " measured the viscosities of some binary and ternary alkali carbonates. Since melt creep must be prevented, a highly sintered alumina crucible was used instead of a gold-plated nickel crucible. Homogeneity of a mixture sample was achieved by gas bubbling. A laser beam is combined with a computer-assisted time counter to obtain the logarithmic decrement. Roscoe s equationi3i has been used for calculation of the viscosity, while it has been claimed by Abe et al. that the viscosities calculated from Roscoe s equation are 0.6-1.5% lower than those from more rigorous equations. 

Melt creep viscosity by according to procedure MVS Patent i By capillary rheometer ASTM D 2116 15) Melt flow rate by ASTM D 2116 By capillary rheometer ASTM D 3307... 

Melt Creep Viscosity - A viscosity value measured for polytetrafluoroethylene using a dynamic mechanical analyzer (DMA). 

Melt creep viscosity by according to procedure MVS Patent. 

Frank, A., Meissner, J. The influence of blending polystyrenes of narrow molecular weight distribution on melt creep flow and creep recovery in elongation. RheoL Acta (1984) 23, pp. 117-... 

Modified ETEE is less dense, tougher, and stiffer and exhibits a higher tensile strength and creep resistance than PTEE, PEA, or EEP resins. It is ductile, and displays in various compositions the characteristic of a nonlinear stress—strain relationship. Typical physical properties of Tef2el products are shown in Table 1 (24,25). Properties such as elongation and flex life depend on crystallinity, which is affected by the rate of crysta11i2ation values depend on fabrication conditions and melt cooling rates. 

Creep. The phenomenon of creep refers to time-dependent deformation. In practice, at least for most metals and ceramics, the creep behavior becomes important at high temperatures and thus sets a limit on the maximum appHcation temperature. In general, this limit increases with the melting point of a material. An approximate limit can be estimated to He at about half of the Kelvin melting temperature. The basic governing equation of steady-state creep can be written as foUows ... 

Refractoriness. Most refractories are mixtures of different oxides, sometimes with significant quantities of impurities. Thus, they do not have sharp melting points but a softening range. Refractoriness is the resistance to physical deformation under the influence of temperature. It is determined by the pyrometric cone equivalent (PCE) test for aluminosiHcates and resistance to creep or shear at high temperature (see Analytical methods). 

Controlled stress viscometers are useful for determining the presence and the value of a yield stress. The stmcture can be estabUshed from creep measurements, and the elasticity from the amount of recovery after creep. The viscosity can be determined at very low shear rates, often ia a Newtonian region. This 2ero-shear viscosity, T q, is related directly to the molecular weight of polymer melts and concentrated polymer solutions. 

Rheometric Scientific markets several devices designed for characterizing viscoelastic fluids. These instmments measure the response of a Hquid to sinusoidal oscillatory motion to determine dynamic viscosity as well as storage and loss moduH. The Rheometric Scientific line includes a fluids spectrometer (RFS-II), a dynamic spectrometer (RDS-7700 series II), and a mechanical spectrometer (RMS-800). The fluids spectrometer is designed for fairly low viscosity materials. The dynamic spectrometer can be used to test soHds, melts, and Hquids at frequencies from 10 to 500 rad/s and as a function of strain ampHtude and temperature. It is a stripped down version of the extremely versatile mechanical spectrometer, which is both a dynamic viscometer and a dynamic mechanical testing device. The RMS-800 can carry out measurements under rotational shear, oscillatory shear, torsional motion, and tension compression, as well as normal stress measurements. Step strain, creep, and creep recovery modes are also available. It is used on a wide range of materials, including adhesives, pastes, mbber, and plastics. 

Solders. In spite of the wide use and development of solders for millennia, as of the mid-1990s most principal solders are lead- or tin-based alloys to which a small amount of silver, zinc, antimony, bismuth, and indium or a combination thereof are added. The principal criterion for choosing a certain solder is its melting characteristics, ie, soHdus and Hquidus temperatures and the temperature spread or pasty range between them. Other criteria are mechanical properties such as strength and creep resistance, physical properties such as electrical and thermal conductivity, and corrosion resistance. 

Pipe fittings require quite high tensile and creep resistance they are thus molded from compounds that have less melt flow than for thin-waHed housings. Plasticized compounds are injection-molded into a variety of parts requiring elastomeric properties. 

---