Mechanical properties phase

In [ 1991 Par] the cast iron containing small contents of Cu and Mo was studied aiming to improve mechanical properties. Phase transformations during heat treatment and flieir influence on strengfli, ductility and fracture toughness were established. 

NR/poly(methyl methacrylate) blends have been the most widely used NR/ plastic blends. However, they have poor mechanical properties. Phase separation was found at the interface and indicated that these blends were immiscible. The interfacial adhesion between the NR and poly(methyl methacrylate) surfaces could be increased by adding a graft copolymer of NR-grfl/f-poly(methyl methacrylate) as a compatibilizer for improving the deformation nature of the polymer blends. Thus, these compatibilized NR/ poly(methyl methacrylate) blends have improved mechanical properties compared to the uncompatibilized blends. 

Kinloch, AJ., Taylor, A.C., 2011. Nano-Composite Relationships between Nano-Structure and Mechanical Properties Phase n. Final Technical Report. Imperial College London, UK. 

Siegel R W 1996 Gas phase synthesis and mechanical properties of nanomaterials Analysis 24 M10... 

Block copolymers are closer to blends of homopolymers in properties, but without the latter s tendency to undergo phase separation. As a matter of fact, diblock copolymers can be used as surfactants to bind immiscible homopolymer blends together and thus improve their mechanical properties. Block copolymers are generally prepared by sequential addition of monomers to living polymers, rather than by depending on the improbable rjr2 > 1 criterion in monomers. 

Properties of Dense Silicon Carbide. Properties of the SiC stmctural ceramics are shown in Table 1. These properties are for representative materials. Variations can exist within a given form depending on the manufacturer. Figure 2 shows the flexure strength of the SiC as a function of temperature. Sintered or sinter/HIP SiC is the preferred material for appHcations at temperatures over 1400°C and the Hquid-phase densified materials show best performance at low temperatures. The reaction-bonded form is utilized primarily for its ease of manufacture and not for superior mechanical properties. 

Table 13 is a representative Hst of nickel and cobalt-base eutectics for which mechanical properties data are available. In most eutectics the matrix phase is ductile and the reinforcement is britde or semibritde, but this is not invariably so. The strongest of the aHoys Hsted in Table 13 exhibit ultimate tensile strengths of 1300—1550 MPa. Appreciable ductiHty can be attained in many fibrous eutectics even when the fibers themselves are quite britde. However, some lamellar eutectics, notably y/y —5, reveal Htde plastic deformation prior to fracture. 

Blends with good mechanical properties can be made from DMPPO and polymers with which DMPPO is incompatible if an appropriate additive, compatibilizing agent, or treatment is used to increase the dispersion of the two phases. Such blends include mixtures of DMPPO with nylon, polycarbonate, polyester, ABS, and poly(phenylene sulfide). 

Mechanical properties of mbber-modifted epoxy resins depend on the extent of mbber-phase separation and on the morphological features of the mbber phase. Dissolved mbber causes plastic deformation and necking at low strains, but does not result in impact toughening. The presence of mbber particles is a necessary but not sufficient condition for achieving impact resistance. Optimum properties are obtained with materials comprising both dissolved and phase-separated mbber (305). 

The microstmcture and imperfection content of coatings produced by atomistic deposition processes can be varied over a very wide range to produce stmctures and properties similar to or totally different from bulk processed materials. In the latter case, the deposited materials may have high intrinsic stress, high point-defect concentration, extremely fine grain size, oriented microstmcture, metastable phases, incorporated impurities, and macro-and microporosity. AH of these may affect the physical, chemical, and mechanical properties of the coating. 

---