Mechanical properties and strength

J. Kettunen, E. A. Makelaa, H. Miettinen, et al., Mechanical properties and strength retention of carbcm fiber-reinforced liquid crystalline polymer (LCP/CF) composite An experimental study on rabbits, Biomaterials 19 1219-1228 (1998). 

Finally, in commercial catalysts silicoaluminates and fiberglass are also used as additives to improve the catalyst mechanical properties and strength. 

The most important disadvantages are moderate and ( -ff), relatively high temperature coefficients (xB and CcJT, and poor mechanical properties (low strength, brittleness). The moderate B and perhaps the less serious, as a larger cross-sectional area produces the requited flux. 

Mechanical Properties and Structural Performance. As a result of the manufacturing process, some cellular plastics have an elongated cell shape and thus exhibit anisotropy in mechanical, thermal, and expansion properties (35,36). Efforts are underway to develop manufacturing techniques that reduce such anisotropy and its effects. In general, higher strengths occur for the paraHel-to-rise direction than in the perpendicular-to-rise orientation. Properties of these materials show variabiUty due to specimen form and position in the bulk material and to uncertainty in the axes with respect to direction of foam rise. Expanded and molded bead products exhibit Httie anisotropy. 

Mechanical Properties and Stability at Elevated Temperature. One increasingly important characteristic of carbon fibers is their excellent performance at elevated temperatures. Strength tested in an inert environment remains constant or slightly increases to temperatures exceeding 2500°C. Amoco s high modulus pitch carbon fiber P-50 maintains approximately 80% of room temperature modulus at temperatures up to 1500°C, then decreases more rapidly to 30% at 2800°C (64). The rapid decrease in modulus is a result of increased atomic mobiHty, increa sing fiber plasticity. 

This computation is also referred to as calculating the zinc equivalent of the alloy. The increase in strength in this alloy series is caused by increased amounts of beta phase in the stmcture. The silicon brasses show similar hardening effects accompanying a second phase. Typical mechanical properties and electrical conductivity for various cast alloys are shown in Table 2. 

Bronzes are somewhat similar to brasses in mechanical properties and to high-zinc brasses in corrosion resistance (except that bronzes are not affected by stress cracking). Aluminum and silicon bronzes are very popiilar in the process industries because they combine good strength with corrosion resistance. 

Alloy 400 has good mechanical properties and is easy to fabricate in all wrought forms and castings. K-500 is a modified version of this alloy and can be thermally treated and is suitable for items requiring strength, as well as corrosion resistance. Alloy 400 has immunity to stress corrosion cracking and pitting in chlorides and caustic alkali solutions. 

Sisal, flax, and glass fiber MTs can be classified by their mechanical properties, tensile strength, and Young s modulus (Table 12). 

Bolts. Bolts shall conform to one of the applicable SAE, ASTM, or AISC specifications. Other bolts not covered by these specifications may be used provided the chemical, mechanical, and physical properties conform to the limits guaranteed by the bolt manufacturer. Certified reports shall constitute sufficient evidence of conformity with the specification. Bolts of different mechanical properties and of the same diameter shall not be mixed on the same drilling or servicing structure to avoid the possibility of bolts of relatively low strength being used where bolts of relatively high strength are required. 

Currently, more SBR is produced by copolymerizing the two monomers with anionic or coordination catalysts. The formed copolymer has better mechanical properties and a narrower molecular weight distribution. A random copolymer with ordered sequence can also be made in solution using butyllithium, provided that the two monomers are charged slowly. Block copolymers of butadiene and styrene may be produced in solution using coordination or anionic catalysts. Butadiene polymerizes first until it is consumed, then styrene starts to polymerize. SBR produced by coordinaton catalysts has better tensile strength than that produced by free radical initiators. 

The mechanical properties including strength, ductility and creep resistance can be affected below these temperature. 

---