Marking and identification

Eollowing agarose gel electrophoresis. Southern blotting can be used for more advanced analysis of separated DNA bands, allowing marking and identification of specific DNA sequences. 

The effects of a rather distinct deformed shell at = 152 were clearly seen as early as 1954 in the alpha-decay energies of isotopes of californium, einsteinium, and fermium. In fact, a number of authors have suggested that the entire transuranium region is stabilized by shell effects with an influence that increases markedly with atomic number. Thus the effects of shell substmcture lead to an increase in spontaneous fission half-Hves of up to about 15 orders of magnitude for the heavy transuranium elements, the heaviest of which would otherwise have half-Hves of the order of those for a compound nucleus (lO " s or less) and not of milliseconds or longer, as found experimentally. This gives hope for the synthesis and identification of several elements beyond the present heaviest (element 109) and suggest that the peninsula of nuclei with measurable half-Hves may extend up to the island of stabiHty at Z = 114 andA = 184. 

Quality System shall provide for control of material and product identification during all stages of production and delivery. Identification is based on applicable drawings, specifications, or other documents. When required or specified, complete traceability of material or product shall be maintained by issuing unique or batch control numbers and/or markings. The identification and trace-ability procedure shall be fully documented to provide objective evidence of compliance with this Code in accordance with this requirement. 

The introduction of the sulfa drugs was followed by the development of the penicillin antibiotics. Fleming s chance observation of the anti-bacterial action of the penicillin mold in 1928 and the subsequent isolation and identification of its active constituent by Florey and Chain in 1940 marked the beginning of the antibiotics era that still continues today. At roughly the same time, the steroid hormones found their way into medical practice. Cortisone was introduced by the pharmaceutical industry in 1944 as a drug for the treatment of arthritis and rheumatic fever. This was followed by the development of steroid hormones as the active constituents of the contraceptive pill. 

Figure 2.9 Phase diagram for C02, showing solid-gas (S + G, sublimation ), solid-liquid (S + L, fusion ), and liquid-gas (L + G, vaporization ) coexistence lines as PT boundaries of stable solid, liquid, or gaseous phases. The triple point (triangle), critical point (x), and selected 280K isotherm of Fig. 2.8 (circle) are marked for identification. Note that the fusion curve tilts slightly forward (with slope 75 atm K-1) and that the sublimation and vaporization curves meet with slightly discontinuous slopes (angle < 180°) at the triple point. The dotted and dashed half-circle shows two possible paths between a liquid (cross-hair square) and a gas (cross-hair circle) state, one discontinuous (dashed) crossing the coexistence line, the other continuous (dotted) encircling the critical point (see text).

Schier R, Balint RF, McCall A, Apell G, Larrick JW, Marks JD, Identification of functional and structural amino-acid residues by parsimonious mutagenesis, Gene, 169 147-155, 1996. 

An empirical relationship has been shown between the contact angles for wettability of a polymer film and the degree to which photooxidation products have accumulated in the surface layers of the film. Changes in wettability of polymer films during photooxidation are markedly dependent on the nature of the polymer. In the detection and identification of the earliest processes and products of surface photooxidation, the wettability method is far more sensitive than the infrared transmission or attenuated reflectance spectra and is about as sensitive but more specific than the ultraviolet transmission spectrum. Contact angle measurements themselves can be used as leads in the selection of solvents for the separation and identification of photooxidation products formed in the surface layers of a polymer film and are potentially useful in establishment of rates of specific processes. 

A quantitative composition, including the name and amount of each active and inactive ingredient contained in the drug product, should be provided. In addition, an overall description of the dosage form should be included. This should be in sufficient detail to characterize it fully with regard to its type, release properties (i.e., immediate versus sustained or controlled release), and physical characteristics such as shape, color, type of coating, hardness, scoring, and identification marks. 

---