Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Load analyzed

Define — Load Analyze ft finer I Define 8, Analyzed filler EXTOrt... [Pg.305]

The result of this experiment include measures of the comprehension level of the overlapped tasks and Serial task as well as the psychological load and the physiological load. Analyzing these measured values separately allows us to examine the following the comprehension level to the overlapped voices when it is assumed to participate in multiple teleconference, the mental load when participating in multitask system. The following sections summarize the results of the experiment. [Pg.190]

To minimize the multiple path and mass transfer contributions to plate height (equations 12.23 and 12.26), the packing material should be of as small a diameter as is practical and loaded with a thin film of stationary phase (equation 12.25). Compared with capillary columns, which are discussed in the next section, packed columns can handle larger amounts of sample. Samples of 0.1-10 )J,L are routinely analyzed with a packed column. Column efficiencies are typically several hundred to 2000 plates/m, providing columns with 3000-10,000 theoretical plates. Assuming Wiax/Wiin is approximately 50, a packed column with 10,000 theoretical plates has a peak capacity (equation 12.18) of... [Pg.564]

Batch Reactors In the simplest land of investigation, reactants can be loaded into a number of ampules, kept in a thermostatic bath for various periods, and analyzed. [Pg.707]

At this point, as far as shaking forces go, the gas forces do not make a contribution. If the rod load or bearing loads are to be analyzed, the gas forces must be calculated and added vectorially to the inertia forces to... [Pg.381]

The path of failure of an adhesive joint can give information about the mechanism of failure if analysis of the elemental and chemical composition can be conducted along the path. Several authors have performed such analyses by loading the adhesive joint until it fractures and then using XPS to analyze each side of the fracture. [Pg.27]

Heating and cooling load calculation for HVAC system design is based on the heat balance principle. For the given building, room, or independent building zone, heat balance components should be established and analyzed. The ma or heat sources and sinks in industrial buildings are ... [Pg.423]

The fundamental analysis of a laminate can be explained, in principle, by use of a simple two-layered cross-ply laminate (a layer with fibers at 0° to the x-direction on top of an equal-thickness layer with fibers at 90° to the x-direction). We will analyze this laminate approximately by considering what conditions the two unbonded layers in Figure 4-3 must satisfy in order for the two layers to be bonded to form a laminate. Imagine that the layers are separate but are subjected to a load in the x-direction. The force is divided between the two layers such that the x-direction deformation of each layer is identical. That is, the laminae in a laminate must deform alike along the interface between the layers or else fracture must existl Accordingly, deformation compatibility of layers is a requirement for a laminate. Because of the equal x-direction deformation of each layer, the top (0°) layer has the most x-direction ress because it is stiffer than the bottom (90°) layer in the x-direction./ Trie x-direction stresses in the top and bottom layers can be shown to have the relation... [Pg.188]

As an example of the contrast between analysis and design, consider the column buckling problem. To analyze the buckling resistance of a simply supported, axially loaded column, we use the Euler-Bernoulli equation,... [Pg.374]

Suppose we want to analyze the stresses in the two stiffeners. The geometry of the sandwich-blade stiffener is actually more complicated and less amenable to analysis than is the hat-shaped stiffener. Issues that arise in the analysis to determine the influence of the various portions of the stiffeners include the in-plane shear stiffness. In the plane of the vertical blade is a certain amount of shear stiffness. That is, the shear stiffness is necfessary to transfer load from the 0° fibers at the top of the stiffener down to the panel. In hat-shaped stiffeners, that shear stiffness is the only way that load is transferred from the 0° fibers at the top of the stiffener down to the panel. Thus, shear stiffness is the dominant issue in the design. And that is why we typically put 45° fibers in the web of the hat-shaped stiffener. [Pg.407]

Analyze all nitrogen tankers before off-loading (see Section 12.3.4)."... [Pg.100]

Liquid nitrogen should always be analyzed before it is off-loaded. The same applies in other cases where delivery of the wrong material could have serious unwanted results, such as a fire or runaway reaction, as in the two incidents that follow. If analysis causes too much delay, the new load should be put in a holding tank. [Pg.269]


See other pages where Load analyzed is mentioned: [Pg.398]    [Pg.4079]    [Pg.4096]    [Pg.623]    [Pg.409]    [Pg.100]    [Pg.72]    [Pg.398]    [Pg.4079]    [Pg.4096]    [Pg.623]    [Pg.409]    [Pg.100]    [Pg.72]    [Pg.585]    [Pg.198]    [Pg.269]    [Pg.547]    [Pg.202]    [Pg.417]    [Pg.194]    [Pg.302]    [Pg.327]    [Pg.420]    [Pg.750]    [Pg.1115]    [Pg.1727]    [Pg.290]    [Pg.490]    [Pg.569]    [Pg.654]    [Pg.23]    [Pg.206]    [Pg.1151]    [Pg.119]    [Pg.408]    [Pg.894]    [Pg.41]    [Pg.168]    [Pg.259]    [Pg.290]    [Pg.360]    [Pg.381]    [Pg.332]   
See also in sourсe #XX -- [ Pg.305 , Pg.335 , Pg.565 ]




SEARCH



© 2024 chempedia.info