Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Injection moulding polymerisation processes

The metathesis polymerisation of dicyclopentadiene, an inexpensive monomer (commercially available cyclopentadiene dimer produced by a Diels-Alder addition reaction containing ca 95 % endo and ca 5 % exo form), leads to a polymer that may be transformed into a technically useful elastomer [144-146, 179] and thermosetting resin [180,181]. The polymerisation has characteristics that make it readily adaptable to the reaction injection moulding ( rim ) process [182], The main feature of this process comes from the fact that the polymerisation is carried out directly in the mould of the desired final product. The active metathesis catalyst is formed when two separate reactants, a precatalyst (tungsten-based) component and an activator (aluminium-based) component, are combined. Monomer streams containing one respective component are mixed directly just before entering the mould, and the polymerisation into a partly crosslinked material takes place directly in this mould (Figure 6.5) [147,168,183-186],... [Pg.369]

RIM is a relatively new process. It can be used for processing of unfilled resin as well as fibre-reinforced composites. The process was discussed in Chapter 1. The process is similar to RTM (discussed previously) with some variation in mould release and reinforcement sizing to optimise resin chemistry with the process. The low viscosity reactant systems facilitate composite materials production, so-called structural RIM composites [19, 20] in which continuous fibre reinforcement mats are placed in mould cavities before injection. Capital investment and operational cost in RIM are therefore much less than those for conventional injection moulding. Polymerisation of a monomer is usually initiated by heat. However, in RIM, the polymerisation is initiated by impingement mixing (not by heat). Hence it is possible to activate polymerisation at relatively low temperature. Unlike RTM, in RIM the mould-fill times are very low ( 1 s) and a cycle time of <60 s is typical. The process is used for the rapid and automated production of large, thin and complex-shaped parts. [Pg.294]

Rigid integral skin structural foams are produced in polyurethane materials by the reaction injection moulding (RIM) process. Components of the polymer are metered via a mixing chamber to give a measured short shot in a tool cavity where the polymerisation and the foaming action, which expands the material to fill the cavity, take place. At the cavity-moulding interface the bubbles formed by the... [Pg.258]

An important development of polymerisation casting is that of reaction injection moulding. Developed primarily for polyurethanes (and discussed further in Chapter 27), the process has also found some use with polyamides and with epoxide resins. [Pg.182]

Figure 6.5 Flow scheme of polydicyclopentadiene production via ring-opening metathesis polymerisation in the reaction injection moulding process... Figure 6.5 Flow scheme of polydicyclopentadiene production via ring-opening metathesis polymerisation in the reaction injection moulding process...
Thermoset processes involve an additional stage of polymerisation and/or chemical crosslinking. The starting materials for reaction injection moulding are of low viscosity, so are easy to mix and pump into the mould. This process is examined at the end of the chapter. [Pg.134]

In order to understand mixing of rubber one has to have a breadth and depth of knowledge, including polymerisation processes and post-mixing processes such as extrusion and injection moulding. [Pg.3]

The basic RIM process is illustrated in Fig. 4.47. A range of plastics lend themselves to the type of fast polymerisation reaction which is required in this process - polyesters, epoxies, nylons and vinyl monomers. However, by far the most commonly used material is polyurethane. The components A and B are an isocyanate and a polyol and these are kept circulating in their separate systems until an injection shot is required. At this point the two reactants are brought together in the mixing head and injected into the mould. [Pg.302]


See other pages where Injection moulding polymerisation processes is mentioned: [Pg.302]    [Pg.302]    [Pg.429]    [Pg.501]    [Pg.19]    [Pg.124]    [Pg.20]    [Pg.67]    [Pg.239]    [Pg.207]    [Pg.429]    [Pg.501]    [Pg.19]    [Pg.50]    [Pg.169]    [Pg.149]    [Pg.21]    [Pg.105]    [Pg.116]    [Pg.328]    [Pg.340]    [Pg.163]    [Pg.429]    [Pg.501]    [Pg.480]    [Pg.718]    [Pg.208]    [Pg.3]    [Pg.201]    [Pg.310]    [Pg.25]   
See also in sourсe #XX -- [ Pg.3 , Pg.4 ]




SEARCH



INJECTION MOULD

Injecting process

Injection processing

Moulding processes

Moulding processes injection

Moulds process

Processing moulding

Processive polymerisation

© 2024 chempedia.info