Hygroscopicity differences

As some bulk sweeteners are hygroscopic, different packaging materials may be necessary for products containing these sweeteners. 

Use approximately 0 5 ml. of glycerol, and cork the flask A securely when weighing the glycerol by difference, owing to the very hygroscopic nature of the latter. Heat on the water-bath for 60 minutes instead of 30 minutes. Excellent results are obtained by this method if a freshly opened sample of anhydrous glycerol is available a sample which has been exposed to the air for even a short period will absorb sufficient water to give inaccurate results. 

Other Borohydrides. Potassium borohydride was formerly used in color reversal development of photographic film and was preferred over sodium borohydride because of its much lower hygroscopicity. Because other borohydrides are made from sodium borohydride, they are correspondingly more expensive. Generally their reducing properties are not sufficiently different to warrant the added cost. Zinc borohydride [17611-70-0] Zn(BH 2> however, has found many appHcations in stereoselective reductions. It is less basic than NaBH, but is not commercially available owing to poor thermal stabihty. It is usually prepared on site in an ether solvent. Zinc borohydride was initially appHed to stereoselective ketone reductions, especially in prostaglandin syntheses (36), and later to aldehydes, acid haHdes, and esters (37). 

The nylons are hygroscopic. Figure 18.16 shows how the equilibrium water absorption of different nylons varies with humidity at room temperature. Figure 18.17 shows how the rate of moisture absorption is affected by the environmental conditions. 

Trifluoromethanesulfonic (triflic) anhydride is commercially available or can be prepared easily by the reaction of triflic acid with phosphorus pentoxide [66] This moderately hygroscopic colorless liquid is a useful reagent for the preparation of various organic derivatives of triflic acid A large variety of organic ionic triflates can be prepared from triflic anhydride A recent example is the preparation of unusual oxo-bridged dicatiomc salts of different types [SS, 89, 90, 91, 92, 93] (equations 38-44) Stabilized dication ether salts of the Huckel aromatic system and some other systems (equations 38 and 39) can be prepared in one step by the... 

Thallium is notably different. TI2O forms as black platelets when TI2CO3 is heated in N2 at 700° (mp 596°, d 10.36 gcm ) it is hygroscopic and gives TlOH with water. Tl" 03 is brown-black (mp 716°, d 10.04gcm ) and can be made by oxidation of aqueous TINO3 with CI2 or Br2 followed by precipitation... 

Traditional infrared spectrophotometers were constructed with mono-chromation being carried out using sodium chloride or potassium bromide prisms, but these had the disadvantage that the prisms are hygroscopic and the middle-infrared region normally necessitated the use of two different prisms in order to obtain adequate dispersion over the whole range. 

Hygroscopicity. It is hygroscopic. When stored in atms of different RH levels for periods up to 40 days, it absorbed the following % of w ... 

Another marked physical difference between sulphides and sulphoxides (or sulphones) is that sulphoxides (and lower alkyl sulphones) are hygroscopic and dissolve quite readily in water or protic solvents such as alcohols, and even more so lower alkyl or alkyl aryl sulphoxides are almost freely miscible with water. This can be accounted for by the formation of the strong hydrogen bond between the S—O bond in the sulphoxides and water molecules. Moreover, lower alkyl sulphoxides and sulphones such as dimethyl sulphoxide (DMSO) or sulpholene can dissolve a number of metallic salts, especially those of alkali and alkaline earth metals, and hence these compounds have been widely utilized as versatile and convenient solvents in modern organic chemistry26 (Table 3). 

Disaccharides like maltose, lactose, and trehalose are used for their similarity to sucrose, but with differences in some properties, such as sweetness, melting point, or hygroscopicity. 

Complete characterization of arylboronic acids is often difficult because they are readily transformed into stable cyclic anhydrides called boroxines5 and other polymeric species. Arylboronic acids are also known to be hygroscopic. Thus, arylboronic acids are often prepared and used directly as a mixture of different entities. Commercial arylboronic acids will very often contain varying amount of anhydrides. 

For the same adsorbent, different mobile phases can be used according to the aim of chromatographic analysis. Rather than preparing an endless line of chromatographic plates of different thickness, it is easier to change the mobile phase up to the most convenient composition, keeping the same characteristics of the stationary phase. In the case of a hygroscopic adsorbent, the adsorbed water influences its activity. 

We have used only two different solvents, deuterochloroform (CDC13) and hexadeuterodimethylsulfoxide (DMSO-d6). The former dissolves a large majority of organic molecules, but DMSO must be used for more polar substances. The disadvantage of DMSO is that it is very hygroscopic, so that even if you try hard to keep it dry you may find small signals due to water in your spectra. Look out for these in the spectra in this book they normally he at about 3.3 ppm. 

Different. Nominal calculation for mine and home but adding calculations which include kerosene heater particles and hygroscopic particles. (Tu et al., 1985)... 

---