Heat capacity table

ENTHALPY, ENTHALPY OF REACTION, AND HEAT CAPACITY TABLE 4.7. Enthalpy Change on Binding PALA to ATCase... 

The thermodynamics experiments are subdivided into experiments on calorimetry and heat capacity, Table XVI phase transitions, Table XVII properties of gases, liquids, solids, solutions and mixtures, Table XVIII and finally equilibrium and miscellaneous thermodynamic topics , Table XIX. 

Heating from 298.15 to 500 K and using Table 4.12b, we estimate a total average heat capacity. Table 4.12c shows the compositions of the inlet and outlet streams and the average heat capacities... 

Lee and Kesler (reference cited) found an accurate representation for compressibility of both gases and liquids by combining BWR-EOS with corresponding states law. They generated departure functions for enthalpy, entropy, fugacity coefficient and heat capacity. Tables are given in Reid et al. (1987), whereas illustrative graphs are presented in Perry (1997). The method is similar to that developed for compressibility. As an example, the enthalpy departure function may be calculated with the relation ... 

Substitute for the heat capacities (Table B.2), integrate, solve for Tusing E-Z Solve=>T = 132°C... 

Geothermal energy in total can be estimated to about 2 10 J, very roughly assuming mean temperatures, densities, and heat capacities (Table 2.17). 

Either equation provides the same information about the heat needed to produce a given change in temperature. As long as we know the molar mass of the substance, it should be simple to convert between the specific heat and the molar heat capacity. Table 9.2 provides a list of specific heats and molar heat capacities for a few materials. A more extensive table can be found in Appendix D. 

In addition to the thermal conductivity, the heat transfer of the compound into the material of the mold wall is an important factor. The heat penetration is determined by the thermal conductivity, density, and specific heat capacity. Table 3.12 shows the values of various commonly used mold materials. BeCu alloys showa very good... 

Consider the simple flowsheet shown in Fig. 6.2. Flow rates, temperatures, and heat duties for each stream are shown. Two of the streams in Fig. 6.2 are sources of heat (hot streams) and two are sinks for heat (cold streams). Assuming that heat capacities are constant, the hot and cold streams can be extracted as given in Table 6.2. Note that the heat capacities CP are total heat capacities and... 

Exampie A.3.1 The pressures for three steam mains have been set to the conditions given in Table A.l. Medium- and low-pressure steam are generated by expanding high-pressure steam through a steam turbine with an isentropic efficiency of 80 percent. The cost of fuel is 4.00 GJ and the cost of electricity is 0.07 h. Boiler feedwater is available at 100°C with a heat capacity... 

For the first pari of this project, we suppose that we are presented with the following experimental data on the heat capacity at constant pressure Cp of solid lead at various temperatures up to and including 298 K (Table 1-2). 

Table 1-2 Experimental Heat Capacities at Constant Pressure for Lead...

A lustrous metal has the heat capacities as a function of temperature shown in Table 1-4 where the integers are temperatures and the floating point numbers (numbers with decimal points) are heat capacities. Print the curve of Cp vs. T and Cp/T vs. T and determine the entropy of the metal at 298 K assuming no phase changes over the interval [0, 298]. Use as many of the methods described above as feasible. If you do not have a plotting program, draw the curves by hand. Scan a table of standard entropy values and decide what the metal might he. 

The heat capacity of thiazole was determined by adiabatic calorimetry from 5 to 340 K by Goursot and Westrum (295,296). A glass-type transition occurs between 145 and 175°K. Melting occurs at 239.53°K (-33-62°C) with an enthalpy increment of 2292 cal mole and an entropy increment of 9-57 cal mole °K . Table 1-44 summarizes the variations as a function of temperature of the most important thermodynamic properties of thiazole molar heat capacity Cp, standard entropy S°, and Gibbs function - G°-H" )IT. 

The tables in this section contain values of the enthalpy and Gibbs energy of formation, entropy, and heat capacity at 298.15 K (25°C). No values are given in these tables for metal alloys or other solid solutions, for fused salts, or for substances of undefined chemical composition. 

TABLE 6.1 Enthalpies and Gibbs Energies of Formation, Entropies, and Heat Capacities of Organic Compounds... 

---