Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Glass-transition temperature pressure

The porous electrodes in PEFCs are bonded to the surface of the ion-exchange membranes which are 0.12- to 0.25-mm thick by pressure and at a temperature usually between the glass-transition temperature and the thermal degradation temperature of the membrane. These conditions provide the necessary environment to produce an intimate contact between the electrocatalyst and the membrane surface. The early PEFCs contained Nafton membranes and about 4 mg/cm of Pt black in both the cathode and anode. Such electrode/membrane combinations, using the appropriate current coUectors and supporting stmcture in PEFCs and water electrolysis ceUs, are capable of operating at pressures up to 20.7 MPa (3000 psi), differential pressures up to 3.5 MPa (500 psi), and current densities of 2000 m A/cm. ... [Pg.578]

The TPX experimental product of Mitsubishi Petrochemical Ind. (221) is an amorphous, transparent polyolefin with very low water absorption (0.01%) and a glass-transition temperature comparable to that of BPA-PC (ca 150°C). Birefringence (<20 nm/mm), flexural modulus, and elongation at break are on the same level as PMMA (221). The vacuum time, the time in minutes to reach a pressure of 0.13 mPa (10 torr), is similarly short like that of cychc polyolefins. Typical values of TPX are fisted in Table 11. A commercial application of TPX is not known as of this writing. [Pg.162]

Two resin systems based on this chemical concept are commercially available from Shell Chemical Company/Technochemie under the COMPIMIDE trademark COMPIMIDE 183 (34) [98723-11-2], for use in printed circuit boards, and COMPIMIDE 796 [106856-59-1], as a resin for low pressure autoclave mol ding (35). Typical properties of COMPIMIDE 183 glass fabric—PCB laminates are provided in Table 8. COMPIMIDE 183 offers a combination of advantageous properties, such as a high glass transition temperature, low expansion coefficient, and flame resistance without bromine compound additives. [Pg.26]

A second general criterion for pressure sensitivity is that the glass transition temperature of the adhesive be below the use temperature, which is usually room temperature. Broadly speaking, the To will be about 30-70°C below room temperature, depending on the base polymer and any added modifiers. [Pg.466]

Tackifying resins enhance the adhesion of non-polar elastomers by improving wettability, increasing polarity and altering the viscoelastic properties. Dahlquist [31 ] established the first evidence of the modification of the viscoelastic properties of an elastomer by adding resins, and demonstrated that the performance of pressure-sensitive adhesives was related to the creep compliance. Later, Aubrey and Sherriff [32] demonstrated that a relationship between peel strength and viscoelasticity in natural rubber-low molecular resins blends existed. Class and Chu [33] used the dynamic mechanical measurements to demonstrate that compatible resins with an elastomer produced a decrease in the elastic modulus at room temperature and an increase in the tan <5 peak (which indicated the glass transition temperature of the resin-elastomer blend). Resins which are incompatible with an elastomer caused an increase in the elastic modulus at room temperature and showed two distinct maxima in the tan <5 curve. [Pg.620]

The arrangement is then placed in a furnace, heated to 800°C, and the pressure decay test is repeated. The setup can be subjected to thermal cycles with pressure decay tests at room temperature and at 800°C. A good hermetic seal, however, will not show any pressure decay at a low pressure differential. The results of one series of tests using a glass composite material that has a glass transition temperature (Tg) of about 700°C, at 5 psi are shown in Figure 5.10. The combination of pressure and thermal cycle tests showed that the seal is capable of withstanding the pressure... [Pg.231]


See other pages where Glass-transition temperature pressure is mentioned: [Pg.207]    [Pg.233]    [Pg.406]    [Pg.155]    [Pg.368]    [Pg.57]    [Pg.257]    [Pg.223]    [Pg.229]    [Pg.89]    [Pg.331]    [Pg.364]    [Pg.139]    [Pg.2002]    [Pg.2004]    [Pg.332]    [Pg.3]    [Pg.1077]    [Pg.615]    [Pg.565]    [Pg.568]    [Pg.15]    [Pg.17]    [Pg.578]    [Pg.143]    [Pg.180]    [Pg.466]    [Pg.688]    [Pg.170]    [Pg.271]    [Pg.693]    [Pg.109]    [Pg.110]    [Pg.16]    [Pg.146]    [Pg.65]    [Pg.209]    [Pg.199]    [Pg.365]    [Pg.19]    [Pg.247]    [Pg.10]    [Pg.496]    [Pg.199]    [Pg.384]   
See also in sourсe #XX -- [ Pg.799 ]

See also in sourсe #XX -- [ Pg.82 ]




SEARCH



Temperature and pressure dependence of relaxation near the glass transition

Transition pressures

© 2024 chempedia.info