Glass calcium

In fluoride glasses, calcium fluoride is an essential constituent, but generally cryolite, NajAlFg, is also added as a flux to lower the temperature of fusion. Aluminium orthophosphate is also generally added to the fusion mixture for various reasons. Of course, the various elements may be added in different ways. Thus, calcium orthophosphate, aluminium fluoride and sodium carbonate are often used in the preparation of fluoride glasses. 

Compositions of high-alumina cement containing quartz or glass, calcium carbonate, microsilica, carbon black, iron oxide red mud or screened fly ash, and styrene-butadiene latex have been described [141,1803,1804]. 

Whereas McGee [188] did not verify any effect of particulate fillers (i.e., glass, calcium carbonate, and aluminum) on the reaction kinetics, Lem and Han [185], working with calcium carbonate and clay in an unsaturated polyester resin, concluded that the reaction rate increases by increasing the filler content. 

Many other systems have subsequently been found to display anion conductivity. The electrical conductivity of lead fluoroborate and fluorogermanate glasses is similar to that of the lead fluorosilicate glasses. Calcium fluoroaluminate glasses also conduct by fluorine migration. Fluorophosphate glasses have also proven to be good anionic conductors. All of these systems are free of alkali ions. 

Glass WoUastonite C- Whiskers Synthetic Cellulose Mica Talcum Graphite Sand/ Silica Kaolin Glass Calcium Metal Soot... 

Aluminum hydroxide Borosilicate glass Calcium monocarbonate Cotton (Gossypium herbaceum) Dolomite Kaolin Lignin Mica Paraffin, chlorinated Pyrophyllite... 

C-glass Calcium borosilicate glasses used in corrosive acid environments ... 

R-glass Calcium aluminosilicate glasses used where added strength and acid corrosion resistance are required ... 

Ceramics and Glasses Calcium phosphate Bone regeneration... 

Basic copper(ll) carbonate Cobalt(ll) stannate Cobalt(ll)-doped alumina glass Calcium copper(ll) silicate Sulfur radical anions in a sodium aluminosilicate matrix Barium manganate(VII) sulfete Copper(ll) phthalocyanine Basic oopper(ll) sulfete Iron(lll) hexacyanoferrate(ll) Cobalt(ll) silicate Basic copper(ll)... 

This is used extensively for qualitative analysis, for it is a rapid process and requires simple apparatus. The adsorbent is usually a layer, about 0 23 mni. thick, of silica gel or alumina, with an inactive binder, e.g. calcium sulphate, to increase the strength of the layer.. A. i i slurry of the absorbent and methanol is commonly coated on glass plates (5 20 cm. or 20 x 20 cm.), but microscope... 

Lead formate separates from aqueous solution without water of crystallisation. It can therefore be used for the preparation of anhydrous formic acid. For this purpose, the powdered lead formate is placed in the inner tube of an ordinary jacketed cond ser, and there held loosely in position by plugs of glass-wool. The condenser is then clamped in an oblique position and the lower end fitted into a receiver closed with a calcium chloride tube. A current of dry hydrogen sulphide is passed down the inner tube of the condenser, whilst steam is passed through the jacket. The formic acid which is liberated... 

Place 0 5 ml. of the pyridine in a 200 ml. round- or flat-bottomed flask and add 34 ml. (30 g.) of benzene. Fit the flask with a reflux water-condenser, and then place it in a cold water-bath. If the experiment is conducted in a fume-cupboard, the top of the condenser can be closed with a calcium chloride tube bent downwards (as in Fig. 61, p. 105 or in Fig. 23(A), p. 45, where the outlet-tube A will carry the calcium chloride tube) and the hydrogen bromide subsequently allowed to escape if, however, the experiment is performed in the open laboratory, fit to the top of the condenser (or to the outlet-tube A) a glass delivery-tube which leads through a piece of rubber tubing to an inverted glass funnel, the rim of which dips just below the surface of some water... 

For this preparation, which must be performed in the fume-cupboard, assemble the apparatus shown in Fig. 67(A). C is a 150 ml. distilling-flask, to the neck of which is fitted a reflux single-surface water-condenser D, closed at the top E by a calcium chloride tube. The side-arm of C carries a cork F which fits the end E of the condenser for subsequent distillation. The side-arm of C is meanwhile plugged by a small rubber cork, or by a short length of glass rod. (Alternatively, use the ground-glass flask and condenser (Fig. 22 (a) and (c), p. 43), and... 

Fig. 77,13, 1 illustrates a distillation unit when it is desired to protect the distillate from moisture in the atmosphere. The drying tube may be filled with anhydrous calcium chloride held in position by loose plugs of glass wool or with a loose plug of cotton wool. Fig. 77,13, 2 depicts the use of an air condenser for liquids of boiling point above 140-150°. 

Higher alcohols. These may be purified by drying with anhydrous potassium carbonate or with anhydrous calcium sulphate, and fractionated after filtration from the desiccant. Bark corks (or ground glass joints) should be used rubber stoppers are slightly attacked. The boiUng points of the fractions to be collected are as follows —... 

---