Gamma surface

Figure 5.37 depicts the basic set up of a wireline logging operation. A sonde is lowered downhole after the drill string has been removed. The sonde is connected via an insulated and reinforced electrical cable to a winch unit at the surface. At a speed of about 600m per hour the cable Is spooled upward and the sonde continuously records formation properties like natural gamma ray radiation, formation resistivity or formation density. The measured data is sent through the cable and is recorded and processed in a sophisticated logging unita the surface. Offshore, this unit will be located in a cabin, while on land it is truck mounted. In either situation data can be transmitted in real time via satellite to company headquarters if required. 

To add surface area, the supports are uniformly coated with a slurry of gamma-alumina and recalcined under moderate conditions. The wash coat acts to accept the active metals, typically low levels of platinum and palladium, in a conventional impregnation process. In the United States in passenger car apphcations the spherical catalyst is used almost exclusively, and methods have been developed to replace the catalyst without removing the converter shell when vehicle inspection reveals that emission standards are not met. 

Support-phase changes or loss of surface area are, of course, irreversible, and replacement of the catalyst may be appropriate. Catalyst damage may take the form of phase changes to the alumina support from gamma to theta or alpha phase. The last is catalyticaky inert because of insignificant surface area. Theta alumina has a low surface area (< 100 /g) relative to gamma alumina (180 m /g) and has poor halogen retention. 

The most widely used exhaust control device consists of a ceramic monolith with a thin-waHed open honeycomb stmcture. The accessible surface of this monolith system is iacreased by applyiag a separate coatiag, a wash coat, of a high surface area material such as gamma-alumiaa with the catalyticaHy active species impregaated iato this washcoat. The catalyst aeeds to oxidize hydrocarboas, coavert CO to CO2, and reduce NO. The whole system forms a catalytic converter that, suitably encased, is placed between the engine and the muffler/silencer unit. 

The tendency for high surface area gamma-alumina to siater and lose that cmcial area duriag high temperature operatioa is retarded by the intimate additioa of several perceat of cerium oxide. The mechanism is stiU under debate but may iavolve a surface LN—aluminate species on the alumina. 

Photodegradation of polyethylene waste can be markedly accelerated via its grafting with acrylamide [98], In contrast, photostabilization of polyethylene and polypropylene can be achieved as a result of the grafting of 2-hydroxy-4-(3-methacryloxy-2-hydroxy-propoxy) benzophenone using gamma radiation [ 147], In this case, the grafted compound acting as a U V stabilizer is chemically bound to the backbone chain of the polymer and its evaporation from the surface can be avoided. 

Another way (Anadrill) is to use removable sources. Figure 4-285 shows the sources being installed in the tool at surface. The two sources, neutrons and gammas, are mounted on the same flexible shaft. They are moved from the shield to the sub without being exposed. Furthermore, if the BHA becomes stuck, they can be fished out with an overshot that connects to the fishing head on top of the neutron source. 

The new geosteering system offers measurements at the bit (below the mud motor) of inclination, rpm, azimuthal gamma ray, azimuthal resistivity, and bit resistivity as seen in Figure 4-298. The signals are transmitted electromagnetically to the MWD sub located above the mud motor, then relayed to surface with the standard mud pressure transmission system. To summarize, the following is recorded Just above the drill bit ... 

For steel, passivation is achieved by the surface formation of a tough, adherent mixture of oxides. The passive film is primarily gamma-magnetite (y-Fe203) but also contains gamma-hydrated ferric oxide (y-FeOOH). The film thickness is perhaps 15 A to 30 A (angstrom units). 

The effects of liposome size and surface charge on liposome-mediated delivery of methotrexate-gamma-aspartate to cells in vitro, Biochim. Biophys. Acta, 820, 74-84. 

Alumina, present in the gamma modification, is the most suitable high surface area support for noble metals. The y-Al203 in washcoats typically has a surface area of 150-175 m g However, at high temperatures y-alumina transforms into the alpha phase, and stabilization to prevent this is essential. Another concern is the diffusion of rhodium into alumina, which calls for the application of diffusion barriers. 

---