Fluid lubricants

One of the major advantages of the worm gear is low wear, which is due mostly to a full-fluid lubricant film. In addition, friction can be further reduced using metals having low coefficients of friction. For example, the wheel is typically made of bronze and the worm of highly finished hardened steel. 

Boundary lubrication is perhaps best defined as the lubrication of surfaces by fluid films so thin that the friction coefficient is affected by both the type of lubricant and the nature of the surface, and is largely independent of viscosity. A fluid lubricant introduced between two surfaces may spread to a microscopically thin film that reduces the sliding friction between the surfaces. The peaks of the high spots may touch, but interlocking occurs only to a limited extent and frictional resistance will be relatively low. 

Several of the current synthetic semi-fluid lubricants for worm gears are based on a poly-alkaline glycol - which possesses slipperiness . Oxidation and rust-inhibitors are... 

There are certain disadvantages as well as advantages in using grease as a lubricant. Greases do not dissipate heat as well as fluid lubricants, and for low-torque operation tend to offer more resistance than oil. 

Thrust Semi-fluid lubrication state, relatively high friction, lower service pressures with multi-collar version, used at low speeds. 

Currently thousands of system combinations have been programmed on the ARRADCOM s CDC 6600 computer with additions and updates made as received. The program is being enlarged to include reactivity with hydraulic fluids, lubricants, metals, etc. Another data bank-maintained is a Hazard Failure program, which is aimed at warning users about potential problems... 

In lubrication history, research has been mainly focused for a long period on two fields—fluid lubrication and boundary lubrication. In boundary lubrication (BL), lubrication models proposed by Bowdeon and Tabor [5], Adamson [6],... 

Singh, C., and Suiha, P., The Three-Dimensional Reynolds Equation for Micropolar-Fluid Lubricated Bearings, Wear, Vol. 76, No. 2,1982,pp. 199-209. 

PapayAG. 1991. Formulating automatic-transmission fluids. Lubrication Engineering 47 271-275. 

Case Study. Such a situation was found to occur in the duct network shown in Fig. 21 and installed to extract iron oxide dust at various points along a cold strip processing line. The stated problems were insufficient suction at the hoods, buildup of contaminant in the hoods and along the processing line (causing cleanup problems due to eventual mixing with hydraulic fluid, lubricant, water, etc.). Analysis of the system found the following ... 

Industrial fluid lubricants, viscosity system for, 15 237t... 

ORGANIC FILMS Oils or grease (low molecular weight) Vacuum pump fluids Lubricants from air handling unit or other machinery Sweat and oil from personel... 

Aryl derivatives of dibenzothiophene are generally described as being thermally stable up to 400° and are therefore of use as heat-transfer media, dielectric or hydraulic fluids, lubricants, and stationary phases for vapor-phase chromatography. 3-Phenyldibenzothiophene 5,5-dioxide is capable of detecting X, y, or corpuscular radiation when incorporated in photographic film. ... 

Ionic liquids (ILs) are, together with water and supercritical fluids, one of the few alternative media for environmentally friendly processes, which seem to have more possibility of industrial application in the next 10 years. The range of demonstrated or proposed applications of ILs is extraordinary, going from their use as nonvolatile, non-flammable solvents in organic synthesis to catalysts, materials for aiding separations and gas capture, advanced heat transfer fluids, lubricants, antistatics, and so on [2 ]. Surpassing in magnitude the number of potential uses is the number of possible IL compositions, estimated to be in the billions [5]. The term ionic liquids includes all compounds composed exclusively by ions that are liquid... 

The polychlorinated biphenyls (PCBs, coplanar biphenyls) have been used in a large variety of applications as dielectric and heat transfer fluids, lubricating oils, plasticizers, wax extenders, and flame retardants. Their industrial use and manufacture in the USA were terminated by 1977. Unfortunately, PCBs persist in the environment. The products used commercially were actually mixtures of PCB isomers and homologs containing 12-68% chlorine. These chemicals are highly stable and highly lipophilic, poorly metabolized, and very resistant to environmental degradation they bioaccumulate in food chains. Food is the major source of PCB residues in humans. 

Mixed Film Ijibrication. Mixed film lubrication is almost invariably the true state ol affairs when boundary and EP lubrication are encountered, i.c.. an appreciable fraction of the load is carried by the fluid film in the valleys" of the surface w hile the asperities in contact are permitted to carry the halancc of (he load without seizure through ihe beneficent intervention of the boundary or EP lubricant. The very important hreakin process of rubbing surfaces consists in the controlled induction of the number and die size of the surface asperities so that fluid lubrication will prevail for must of ihe lime. 

See ZN/P curve. A less common form of full-fluid-lubrication is hydrostatic lubrication, wherein the oil is supplied to the bearing area under sufficient external pressure to separate the sliding surfaces. 

---