Fluid catalytic cracking catalyst coke

Characterization of Fluid Catalytic Cracking Catalyst Coke by C NMR and Mass Spectrometry... 

Bayraktar, O., and Kugler, E. Characterization of Coke on Equilibrium Fluid Catalytic Cracking Catalysts by Temperature-Programmed Oxidation. Applied Catalysis A General 233 (2002) 197-213. 

Evaluation of Coke Selectivity of Fluid Catalytic Cracking Catalysts... 

The MTO process employs a turbulent fluid-bed reactor system and typical conversions exceed 99.9%. The coked catalyst is continuously withdrawn from the reactor and burned in a regenerator. Coke yield and catalyst circulation are an order of magnitude lower than in fluid catalytic cracking (FCC). The MTO process was first scaled up in a 0.64 m /d (4 bbl/d) pilot plant and a successfiil 15.9 m /d (100 bbl/d) demonstration plant was operated in Germany with U.S. and German government support. 

The most dominant catalytic process in the United States is the fluid catalytic cracking process. In this process, partially vaporized medium-cut petroleum fractions called gas oils are brought in contact with a hot, moving, freshly regenerated catalyst stream for a short period of time at process conditions noted above. Spent catalyst moves continuously into a regenerator where deposited coke on the catalyst is burnt off. The hot, freshly regenerated catalyst moves back to the reactor to contact the hot gas oil (see Catalysts, regeneration). 

Catalytic Pyrolysis. This should not be confused with fluid catalytic cracking, which is used in petroleum refining (see Catalysts, regeneration). Catalytic pyrolysis is aimed at producing primarily ethylene. There are many patents and research articles covering the last 20 years (84—89). Catalytic research until 1988 has been summarized (86). Almost all catalysts produce higher amounts of CO and CO2 than normally obtained with conventional pyrolysis. This indicates that the water gas reaction is also very active with these catalysts, and usually this leads to some deterioration of the olefin yield. Significant amounts of coke have been found in these catalysts, and thus there is a further reduction in olefin yield with on-stream time. Most of these catalysts are based on low surface area alumina catalysts (86). A notable exception is the catalyst developed in the former USSR (89). This catalyst primarily contains vanadium as the active material on pumice (89), and is claimed to produce low levels of carbon oxides. 

Another approach used to reduce the harmful effects of heavy metals in petroleum residues is metal passivation. In this process an oil-soluble treating agent containing antimony is used that deposits on the catalyst surface in competition with contaminant metals, thus reducing the catalytic activity of these metals in promoting coke and gas formation. Metal passivation is especially important in fluid catalytic cracking (FCC) processes. Additives that improve FCC processes were found to increase catalyst life and improve the yield and quality of products. ... 

The modem gasolines are produced by blending products from cmde oil distillation, that is, fluid catalytic cracking, hydrocraking, reforming, coking, polymerization, isomerization, and alkylation.Two clear examples of the possible use of solid-acid catalysts in refining processes are the isomerization of lineal alkanes and the alkylation of isobutene with butanes. In both these cases, and due to the octane... 

McPherson, L. J. Reactor Coking Problems in Fluid Catalytic Cracking Units. Akzo Catalysts Symposium, Scheveningen, The Netherlands, 1984. 

Figure 1731. Fluidized bed reactor processes for the conversion of petroleum fractions, (a) Exxon Model IV fluid catalytic cracking (FCC) unit sketch and operating parameters. (Hetsroni, Handbook of Multiphase Systems, McGraw-Hill, New York, 1982). (b) A modem FCC unit utilizing active zeolite catalysts the reaction occurs primarily in the riser which can be as high as 45 m. (c) Fluidized bed hydroformer in which straight chain molecules are converted into branched ones in the presence of hydrogen at a pressure of 1500 atm. The process has been largely superseded by fixed bed units employing precious metal catalysts (Hetsroni, loc. cit.). (d) A fluidized bed coking process units have been built with capacities of 400-12,000 tons/day.

---