Flowing spins

The air jet textured yam process is based on overfeeding a yam into a turbulent air jet so that the excess length forms into loops that are trapped in the yam stmcture. The air flow is unheated, turbulent, and asymmetrically impinges the yam. The process includes a heat stabilization zone. Key process variables include texturing speed, air pressure, percentage overfeed, filament linear density, air flow, spin finish, and fiber modulus (100). The loops create visual and tactile aesthetics similar to false twist textured and staple spun yams. 

The average flow spin angle can be estimated from the relation... 

The choice of the appropriate relation from the possibilities (19.8) should be restricted by a conservation condition for the average value of the tangent of the flow spin angle... 

If the tangential branch pipe is designed in such a way that nap ap = then e = 0, and the calculation of CE for the tangential branch pipe can be performed in the same way as for the axial one. The only difference is in the definition of the flow spin angle. 

We first examine how this works for the case of coherent flow. A typical pulse sequence is shown in figure Bl.14.9. This sequence creates a spin echo using two unipolar gradient pulses on either side of a 180° pulse. The duration of each gradient pulse of strength G, is . The centres of the gradient pulses are separated by A. 

Figure Bl.14.9. Imaging pulse sequence including flow and/or diflfiision encoding. Gradient pulses before and after the inversion pulse are supplemented in any of the spatial dimensions of the standard spin-echo imaging sequence. Motion weighting is achieved by switching a strong gradient pulse pair G, (see solid black line). The steady-state distribution of flow (coherent motion) as well as diffusion (spatially...

Polymers owe much of their attractiveness to their ease of processing. In many important teclmiques, such as injection moulding, fibre spinning and film fonnation, polymers are processed in the melt, so that their flow behaviour is of paramount importance. Because of the viscoelastic properties of polymers, their flow behaviour is much more complex than that of Newtonian liquids for which the viscosity is the only essential parameter. In polymer melts, the recoverable shear compliance, which relates to the elastic forces, is used in addition to the viscosity in the description of flow [48]. 

Fig. 7. Control of fan performance with inlet vane control. SoHd lines marked A and N show normal performance without vanes (vanes wide open). As vanes are progressively closed, static and power curves are modified as indicated by dashed lines. Intersection ( - ) of the system resistance curve with these reduced pressure curves at points B, C, D, and E shows how imparting more spin to the inlet air reduces flow. Projecting points A to E vertically downward to the corresponding power curve locates fan power points A through E7 Power savings achieved over throttling control can be estimated by projecting points B through E vertically downward to the A power curve and comparing the value with that from the proper reduced power curve. To...

Water is continuously added to the last extraction bath and flows countercurrenfly to filament travel from bath to bath. Maximum solvent concentration of 15—30% is reached in the coagulation bath and maintained constant by continuously removing the solvent—water mixture for solvent recovery. Spinning solvent is generally recovered by a two-stage process in which the excess water is initially removed by distillation followed by transfer of cmde solvent to a second column where it is distilled and transferred for reuse in polymer manufacture. 

Flow processes iaside the spinneret are governed by shear viscosity and shear rate. PET is a non-Newtonian elastic fluid. Spinning filament tension and molecular orientation depend on polymer temperature and viscosity, spinneret capillary diameter and length, spin speed, rate of filament cooling, inertia, and air drag (69,70). These variables combine to attenuate the fiber and orient and sometimes crystallize the molecular chains (71). 

The operating pressure is kept low to reduce air consumption. To obtain high capacities, the disks spin fairly fast (up to 2 or 3 rpm) and this leads to thin cakes which give Htde resistance to air flow the only way to keep this flow within economical limits is to reduce the air pressure in the vessel. 

Cup anemometers have shaped cups mounted on the spokes of a wheel. The cups, under the action of the fluid forces, spin in a horizontal plane about a vertical shaft mounted in bearings. Vane or propeller types use a multibladed rotor, the axis of which is parallel to the flow direction as the rotating member. Both designs are commonly used for wind speed measurement or similar appHcations such as the velocity in ventilation ducts. Because of inertia, anemometers are most accurate under steady conditions. Velocity fluctuations cause readings that are too high. 

Fig. 5. Separation in Latham bowl (a) whole blood is pumped down the feed tube and enters bowl at bottom (b) centrifugal force spins denser cellular components outside, leaving plasma or platelet-rich plasma (PRP) in inner band (c) when bowl is full, plasma flows out effluent tube, followed by platelets and then leukocytes, until bowl is almost completely full of ted cells (d) after draw is completed, bowl stops spinning and uncoUected components are...

---