Excitation, quantum efficiency

The intensity of fluorescence therefore, increases with an increase in quantum efficiency, incident power of the excitation source, and the molar absorptivity and concentration of the fluorescing species. 

Standardizing the Method Equations 10.32 and 10.33 show that the intensity of fluorescent or phosphorescent emission is proportional to the concentration of the photoluminescent species, provided that the absorbance of radiation from the excitation source (A = ebC) is less than approximately 0.01. Quantitative methods are usually standardized using a set of external standards. Calibration curves are linear over as much as four to six orders of magnitude for fluorescence and two to four orders of magnitude for phosphorescence. Calibration curves become nonlinear for high concentrations of the photoluminescent species at which the intensity of emission is given by equation 10.31. Nonlinearity also may be observed at low concentrations due to the presence of fluorescent or phosphorescent contaminants. As discussed earlier, the quantum efficiency for emission is sensitive to temperature and sample matrix, both of which must be controlled if external standards are to be used. In addition, emission intensity depends on the molar absorptivity of the photoluminescent species, which is sensitive to the sample matrix. 

The fluorescent emission for quinine at 450 nm can be induced using an excitation frequency of either 250 nm or 350 nm. The fluorescent quantum efficiency is known to be the same for either excitation wavelength, and the UV absorption spectrum shows that 250 is greater than 350- Nevertheless, fluorescent emission intensity is greater when using 350 nm as the excitation wavelength. Speculate on why this is the case. 

Peroxyoxalate chemiluminescence is the most efficient nonenzymatic chemiluminescent reaction known. Quantum efficiencies as high as 22—27% have been reported for oxalate esters prepared from 2,4,6-trichlorophenol, 2,4-dinitrophenol, and 3-trif1uoromethy1-4-nitropheno1 (6,76,77) with the duorescers mbrene [517-51-1] (78,79) or 5,12-bis(phenylethynyl)naphthacene [18826-29-4] (79). For most reactions, however, a quantum efficiency of 4% or less is more common with many in the range of lO " to 10 ein/mol (80). The inefficiency in the chemiexcitation process undoubtedly arises from the transfer of energy of the activated peroxyoxalate to the duorescer. The inefficiency in the CIEEL sequence derives from multiple side reactions available to the reactive intermediates in competition with the excited state producing back-electron transfer process. 

Nonradiative Decay. To have technical importance, a luminescent material should have a high efficiency for conversion of the excitation to visible light. Photoluminescent phosphors for use in fluorescent lamps usually have a quantum efficiency of greater than 0.75. AH the exciting quanta would be reemitted as visible light if there were no nonradiative losses. 

Fluorescence from the ExcitedSj State. In Figure 1, after absorption (A) and vibrational deactivation (VD) occur, the lowest or nearly lowest level of the singlet excited state is reached. If the molecule is fluorescent with a high quantum efficiency, fluorescent emission of a quantum of... 

Knowledge of photoiaduced electroa-transfer dyaamics is important to technological appUcations. The quantum efficiency, ( ), ie, the number of chemical events per number of photons absorbed of the desired electron-transfer photoreaction, reflects the competition between rate of the electron-transfer process, eg, from Z7, and the radiative and radiationless decay of the excited state, reflected ia the lifetime, T, of ZA ia abseace ofM. Thus,... 

The requited characteristics of dyes used as passive mode-locking agents and as active laser media differ in essential ways. For passive mode-locking dyes, short excited-state relaxation times ate needed dyes of this kind ate characterized by low fluorescence quantum efficiencies caused by the highly probable nonradiant processes. On the other hand, the polymethines to be appHed as active laser media ate supposed to have much higher quantum efficiencies, approximating a value of one (91). 

Excited-state properties of the cyanine and related dyes are complex. Most cyanine dyes exhibit small Stokes shifts for duorescence maxima. Typical carbocyanines (1) with n = 1 show 14- to 16-nm shifts in methanol solution with low quantum efficiencies for duorescence (Op ) of less than 0.05. The diearbocyanine analogues also show small Stokes shifts but higher quantum yields (Lpj = 0.3-0.5). 

PM spectra and their decays in DOO-PPV films and dilute solutions, we conclude that the primary excitations in DOO-PPV films are also singlet excitons [26]. The long excitonic lifetime and a corresponding high PL quantum efficiency [27] indicates that DOO-PPV is a high quality polymer material, which is very suitable for electrooptics and laser action applications [28],... 

The enormous progress in the field of electroluminescent conjugated polymers has led to performances of oiganic light-emitting devices (LEDs) that are comparable and in some aspects superior to their inorganic counterparts 11). Quantum efficiencies in excess of 5% have been demonstrated [2] and show that a high fraction of the injected carriers in a polymeric electroluminescence (EL) device form electronic excitations which recombine radiatively. 

Fluorescent small molecules are used as dopants in either electron- or hole-transporting binders. These emitters are selected for their high photoluminescent quantum efficiency and for the color of their emission. Typical examples include perylene and its derivatives 44], quinacridones [45, penlaphenylcyclopenlcne [46], dicyanomethylene pyrans [47, 48], and rubrene [3(3, 49]. The emissive dopant is chosen to have a lower excited state energy than the host, such that if an exciton forms on a host molecule it will spontaneously transfer to the dopant. Relatively small concentrations of dopant are used, typically in the order of 1%, in order to avoid concentration quenching of their luminescence. 

Between 1923 and 1927, the concepts of quantum efficiency (number of photons emitted divided by number of photons absorbed by a sample) and quantum yield (fraction of excited molecules that emit) had been defined and values determined for many compounds by Vavilov (34). The quantum yield indicates the extent that other energy loss mechanisms compete with emission in an excited molecule. Although the quantum yield is influenced by the molecular environment of the emitter, for a given environment it depends on the nature of the emitting compound and is independent of concentration and excitation wavelength, at least at low concentrations (35). Tlius, it serves as another measurable parameter that can be used to identify the compounds in a sample and also, because of its sensitivity to the surroundings of the luminophore, to probe the environment of the emitter. 

In addition to the photoluminescence red shifts, broadening of photoluminescence spectra and decrease in the photoluminescence quantum efficiency are reported with increasing temperature. The spectral broadening is due to scattering by coupling of excitons with acoustic and LO phonons [22]. The decrease in the photoluminescence quantum efficiency is due to non-radiative relaxation from the thermally activated state. The Stark effect also produces photoluminescence spectral shifts in CdSe quantum dots [23]. Large red shifts up to 75 meV are reported in the photoluminescence spectra of CdSe quantum dots under an applied electric field of 350 kVcm . Here, the applied electric field decreases or cancels a component in the excited state dipole that is parallel to the applied field the excited state dipole is contributed by the charge carriers present on the surface of the quantum dots. 

Producing electron-hole pairs by light excitation in the small particles (d < dg ) electrons and holes can easily be transferred to an electron acceptor and donor, respectively, provided that the energetic requirements are fulfilled. The quantum efficiency of the reaction depends on the transfer rate at the interface, on the recombination rate within the particle and on the transit time, the latter being given by ... 

Direct Photolysis. Direct photochemical reactions are due to absorption of electromagnetic energy by a pollutant. In this "primary" photochemical process, absorption of a photon promotes a molecule from its ground state to an electronically excited state. The excited molecule then either reacts to yield a photoproduct or decays (via fluorescence, phosphorescence, etc.) to its ground state. The efficiency of each of these energy conversion processes is called its "quantum yield" the law of conservation of energy requires that the primary quantum efficiencies sum to 1.0. Photochemical reactivity is thus composed of two factors the absorption spectrum, and the quantum efficiency for photochemical transformations. 

The incident monochromatic photon-to-current conversion efficiency (IPCE), also called external quantum efficiency, is defined as the number of electrons generated by light in the external circuit divided by the number of incident photons as a function of excitation wavelength. It is expressed in Equation (7).29 In most cases, the photoaction spectrum overlaps with the absorption spectrum of the sensitizer adsorbed on the semiconductor surface. A high IPCE is a prerequisite for high-power photovoltaic applications, which depends on the sensitizer photon absorption, excited state electron injection, and electron transport to the terminals ... 

---