2- ethylamine functional group

Polymers containing pendant carbamate functional groups can be prepared by the reaction of phenyl isocyanate with poly(vinyl alcohol) in homogeneous dimethylsulfoxide solutions using a tri-ethylamine catalyst. These modified polymers are soluble in dimethyl sulfoxide, dimethylacetamide, dimethylformamide and formic acid but are insoluble in water, methanol and xylene. Above about 50% degree of substitution, the polymers are also soluble in acetic acid and butyrolactone. The modified polymers contain aromatic, C = 0, NH and CN bands in the infrared and show a diminished OH absorption. Similar results were noted in the NMR spectroscopy. These modified polymers show a lower specific and intrinsic viscosity in DMSO solutions than does the unmodified poly(vinyl alcohol) and this viscosity decreases as the degree of substitution increases. 

In the case of catecholamines, the functional groups of particular interest include the nitrogen atom, the C-2 oxygen atom, the aromatic ring and the aromatic oxygen substituents (see Figures 2 and 7). For compounds I-VIII, the interatomic distances are tabulated in Table VI. These may readily be compared to the corresponding values from x-ray studies of three representative conformationally mobile phenyl-ethylamines, norepinephrine hydrochloride (IX), amphetamine sulfate (X) and mescaline hydrobromide (XI). 

A. Alkaloids of Type I, not containing a Functional Group at C-11.— -Acetyl-cycloprotobuxine-D (124), isolated from B. sempervirens, gives on acetylation the already known iViV -diacetylcycloprotobuxine-D (125). Methylation (HCOjH-HCHO) gives JV-acetylcycloprotobuxine-B (126), which is different from the known N-acetylcycloprotobuxine-C (127). Deacetylation with lithium-ethylamine has not been attempted. 

C. Functional groups containing nitrogen 1 —C—NH2 1 primary amine CH3CH2NH2 ethylamine, smells like ammonia... 

The separation of ethylamines together with the standard cations can also be performed in a simple way with a linear acid gradient by exploiting the selectivity change caused by the crown ether functional groups of lonPac CS15. To... 

Therefore we can identify the presence (or absence) of different functional groups from the absorbance pattern on an infra-red spectrum. Look at the infra-red spectrum of ethylamine in Figure 18.7 ... 

The first stable, crystalline epoxyamine 12 has been reported this versatile new functional group undergoes a variety of reactions leading to a-hydroxyketones, a-hydroxy-N-ethylamines, 1-aziridinocycloheptanones, and aziridinomethyl cyclohexanols. 

When the hardening reaction involves cationic polymerization induced by a Lewis acid, however, the functionality of each epoxy group is 2 and that of structure 1-20 is 4. The general hardening reaction is illustrated in Eq. (1-10) for initiation by BF3, which is normally used in this context as a complex with ethylamine, for easier handling. 

In another approach, reactive monodisperse porous poly(chloromethylstyrene-co-styrene-co-divinylbenzene) beads have been employed for the preparation of chiral HPLC packings. Thus, reactive chloromethyl groups were derivatized to yield amino functionalized beads onto which both rt-basic and rt-acidic type chiral. selectors, (/ )- -(l-naphthyl)ethylamine and (/ )-A -(3.5-dinitrobenzoyl)phenylglycine, respectively, were attached. The resulting chiral particles were chromatographically tested for the enantioseparation of model SAs. Despite the presence of strongly competitive it-TT-binding sites of the styrenic support these chirally modified beads afforded baseline separations for 2,2,2-trifluoro-l-(9-anthryl) ethanol and Af-(3.5-dinitro-benzoyl) leucine enantiomers, respectively [369. ... 

---