Elastomers ozone resistance

Nitrile mbber finds broad application in industry because of its excellent resistance to oil and chemicals, its good flexibility at low temperatures, high abrasion and heat resistance (up to 120°C), and good mechanical properties. Nitrile mbber consists of butadiene—acrylonitrile copolymers with an acrylonitrile content ranging from 15 to 45% (see Elastomers, SYNTHETIC, NITRILE RUBBER). In addition to the traditional applications of nitrile mbber for hoses, gaskets, seals, and oil well equipment, new applications have emerged with the development of nitrile mbber blends with poly(vinyl chloride) (PVC). These blends combine the chemical resistance and low temperature flexibility characteristics of nitrile mbber with the stability and ozone resistance of PVC. This has greatly expanded the use of nitrile mbber in outdoor applications for hoses, belts, and cable jackets, where ozone resistance is necessary. 

The prime installation method is mechanically fastened but fully adhered and ballasted appHcations can also be used. CSPE exhibits strong resistance not only to weathering but also to a broad range of chemicals and pollutants it is also inherently ozone-resistant. It can be produced in many colors and the sheet widths are typically 5—6.5 ft (1.5—1.65 m). The physical characteristics of a CSPE sheet have been described (17) (see Elastomers, SYNTHETIC-Cm OROSULFONATED POLYETHYLENE). 

Physical Factors. Unsatuiated elastomers must be stretched for ozone cracking to occur. Elongations of 3—5% are generally sufficient. Crack growth studies (10—18) have shown that some minimum force, called the critical stress, rather than a minimum elongation is required for cracking to occur. Critical stress values are neady the same for most unsaturated mbbers. However, polychloroprene has a higher critical stress value than other diene mbbers, consistent with its better ozone resistance. It has been found that temperature, plasticization, and ozone concentration have httie effect on critical stress values. 

Ozonc-rcsjstant elastomers which have no unsaturation are an exceUent choice when their physical properties suit the appHcation, for example, polyacrylates, polysulfides, siHcones, polyesters, and chlorosulfonated polyethylene (38). Such polymers are also used where high ozone concentrations are encountered. Elastomers with pendant, but not backbone, unsaturation are likewise ozone-resistant. Elastomers of this type are the ethylene—propylene—diene (EPDM) mbbers, which possess a weathering resistance that is not dependent on environmentally sensitive stabilizers. Other elastomers, such as butyl mbber (HR) with low double-bond content, are fairly resistant to ozone. As unsaturation increases, ozone resistance decreases. Chloroprene mbber (CR) is also quite ozone-resistant. 

Two propylene oxide elastomers have been commercialized, PO—AGE and ECH—PO—AGE. These polymers show excellent low temperature flexibihty and low gas permeabihty. After compounding, PO—AGE copolymer is highly resiUent, and shows excellent flex life and flexibiUty at extremely low temperatures (ca —65°C). It is slightly better than natural mbber in these characteristics. Resistance to oil, fuels, and solvents is moderate to poor. Wear resistance is also poor. Unlike natural mbber, PO—AGE is ozone resistant and resistant to aging at high temperatures. The properties of compounded ECH—PO—AGE he somewhere between those of ECH—EO copolymer and PO—AGE copolymer (22). As the ECH content of the terpolymer increases, fuel resistance increases while low temperature flexibihty decreases. Heat resistance is similar to ECH—EO fuel resistance is similar to polychloroprene. The uncured mbber is soluble in aromatic solvents and ketones. 

Vulcanisation can be effected by diamines, polyamines and lead compounds such as lead oxides and basic lead phosphite. The homopolymer vulcanisate is similar to butyl rubber in such characteristics as low air permeability, low resilience, excellent ozone resistance, good heat resistance and good weathering resistance. In addition the polyepichlorohydrins have good flame resistance. The copolymers have more resilience and lower brittle points but air impermeability and oil resistance are not so good. The inclusion of allyl glycidyl ether in the polymerisation recipe produces a sulphur-curable elastomer primarily of interest because of its better resistance to sour gas than conventional epichlorhydrin rubbers. 

Kennedy, J. P. and Chou,T. Poly (isobutylene-co-fS-Pinene) A New Sulfur Vulcanizable, Ozone Resistant Elastomer by Cationic Isomerization Copolymerization. Vol. 21, pp. 1—39. 

Ozone Resistant Elastomer by Cationic Isomerization Copolymerization. Vol. 21, pp. 1-39. 

The most prevalent approach to achieve long-lasting and nonstaining ozone protection of rubber compounds is to use an inherently ozone-resistant, saturated backbone polymer in blends with a diene rubber. The ozone-resistant polymer must be used in sufficient concentration (minimum 25 phr) and must also be sufficiently dispersed to form domains that effectively block the continuous propagation of an ozone-initiated crack through the diene rubber phase within the compound. Elastomers such as ethylene-propylene-diene terpolymers, halogenated butyl mbbers, or brominated isobutylene-co-para-methylstyrene elastomers have been proposed in combination with NR and/or butadiene rubber. 

The styrenic thermoplastic elastomers are the only type which are fully compounded in the manner of conventional elastomers. In this case, however, the addition of carbon black, or other fillers, does not give reinforcement. Additions of polystyrene, or high impact polystyrene, and oil are used to vary hardness and tear strength, and fillers can be used to cheapen the material. Other added polymers, e g., EVA, can be used to increase ozone resistance. These materials also require antioxidants for protection during processing and service life, and the poor UV stability restricts their use in outdoor applications. 

Fluoroelastomers excel compared to all other elastomers in heat, chemical, flame, weathering, fuel, and ozone resistance. In addition oil, oxygen, and water resistance are very good. The fluoroelastomers, however, are attacked by amines and some highly polar solvents. The abrasion resistance and low temperature properties are adequate for most applications. 

Vinyl Acetate—Ethylene Copolymers. In these random copolymers, the ratio of ethylene to vinyl acetate (EVA) is varied from 30—60%. As the vinyl acetate content increases, the oil and heat resistance increases. With higher ethylene content the physical strength, tensile, and tear increases. The polymers are cured with peroxide. The main properties of these elastomers include heat resistance, moderate oil and solvent resistance, low compression set, good weather resistance, high damping, excellent ozone resistance, and they can be easily colored (see Vinyl polymers, polyvinyl acetate)). 

The copolymer of isobutylene with a few percent isoprenc (butyl rubber) can be cured to produce an ozone-resistant elastomer with low permeability to oxygen and nitrogen. Butyl rubber has a Tt of — 70 C a refractive index of 1.5081, and a coefficient of linear expansion of 5.7 X 10 cm/cxn C. Chloro and bromo butyl rubber are more resistant to the permeation of oxygen and nitrogen than butyl rubber. 

Chlorosulfonated polyethylene A product obtained by treatment of polyethylene by chlorine and sulfur dioxide. It is an elastomer highly resistant to chemicals and ozone. 

---