Effect of Surface Finish

This findings strengthen the need for mirror-polished specimens with an average surface roughness Rj 1 pm to derive reference S-N curves. Intrusions and extrusions are surface defects of the order of some micron (see Sect. 1.4). If surface finish is rather rough leaving material plicas higher than these few microns 

---

The Effect of Surface Finishing on the Corrosion Behaviour of Magnesium Alloys... 

Figure 2.65 Effect of surface finish and hardness on frictional force build-up.

Figure 62 Effects of surface finish and colour on resistance to scratching...

As shown in Fig. 15.12, the active site density may decrease very strongly with contact angle for a given distribution of cavity sizes. It is not surprising, therefore, that the prediction of nucleate boiling heat transfer is bedeviled by the problems of predicting surface behavior. The effect of surface finish on nucleate pool boiling is well illustrated by the results of Brown... 

FIGURE 15.36 Effect of surface finish on nucleate pool boiling of water. Results of Brown [76] (from Rohsenow [2], with permission of The McGraw-Hill Companies). 

Effect of Surface Finish. As was demonstrated in the section on parametric effects, the microstructure of the surface has a dramatic effect on nucleate boiling heat transfer. Based on results obtained by Berenson [149] in 1960, it has generally been asserted that the critical heat... 

Reid, D.C., Bott, T.R. and Miller, R., 1992, Biofouling in stirred tank reactors -effect of surface finish, in Melo, L.F., Bott, T.R., Fletcher, M. and Capdeville, B. eds. Biofilms - Science and Technology, 521 - 526, Kluwer Academic Publishers, Dordrecht. 

Andersson, C.A. and Bratton, R.J., 1979, Effect of surface finish on the strength of hot pressed silicon nitride, in The Science of Ceramic Machining and Surface Finishing n, NBS Special Publication 562, pp. 463- 76. 

Effect of surface finish on the biofouling rates of different materials was studied by standardized harmonic mean (SHM) of drop spread determination method. It was observed among different materials like titanium, stainless steel, admiralty brass etc., carbon steel was the most affected (highest value of SHM). Here the corrosion causing slime formers were gram-negative bacteria like Pseudomonas species. The influence of water quality parameters on... 

Liu, H.W. (1956) Effect of surface finish on the fatigue strength of TiA16V4-alloy. Dept, of Theoretical and Applied Mechanics, University of Illinois, T.U.A.M. Rep. 533. 

The effect of surface finishes on the properties of carbon fiber composites has been discussed by Wright [47,48] and Peebles [49]. 

Figure 2.18 Effect of surface finish and gap size on the shear strength of an anaerobic adhesive. Adhesive DTD 5633/G2 tested to DTD 5628 using given finish and gap.

Stokes, R.J., 1972. Effects of surface finishing on mechanical and other physical properties of ceramics. NBS Spec. Publ. Nr. 348, 343. 

Figure 6.16. Effect of surface finish on sapphire hardness (a) (0001) (b) (1120), with GP = gas polish, G = dry grinding, (c) Effect of Ti dose on AI2O3 surface and its hardness. After Becher. " ... 

Fig. 3.10 Effect of surface finish on fatigue limit of steels (modified from [9])...

S.M. Chung, A.U.J. Yap, Effects of surface finish on indentation modulus and hardness of dental composite restoratives. Dent. Mater. 21(11), 1008-1016 (2005)... 

FIG. 8 The effect of surface finish on the maximum loads measured during pull tests conducted on SOIC device leads soldered with several Pb-free solders and eutectic Sn-Pb. 

---