Dissipated mechanically

One of the primary goals of current research in the area of tribology is to understand how it is that the kinetic energy of a sliding object is converted into internal energy. These dissipation mechanisms detennine the rate of energy flow from macroscopic motion into the microscopic modes of the system. Numerous mechanisms can be... 

The shock wave is subject to other dissipative effects, however, such as viscosity and heat transport. It is these dissipative mechanisms that are responsible for preventing the shock from becoming a true, infinitesimally thin discontinuity. In reality, the velocity gradient can only increase until... 

The fact that shock waves continue to steepen until dissipative mechanisms take over means that entropy is generated by the conversion of mechanical energy to heat, so the process is irreversible. By contrast, in a fluid, rarefactions do not usually involve significant energy dissipation, so they can be regarded as reversible, or isentropic, processes. There are circumstances, however, such as in materials with elastic-plastic response, in which plastic deformation during the release process dissipates energy in an irreversible fashion, and the expansion wave is therefore not isentropic. 

More pertinent to the present topic is the indirect dissipation mechanism, when the reaction coordinate is coupled to one or several active modes which characterize the reaction complex and, in turn, are damped because of coupling to a continuous bath. The total effect of the active oscillators and bath may be represented by the effective spectral density For instance, in the... 

In addition to dissipation of the substance from the model system through degradation, other dissipative mechanisms can be considered. Neely and Mackay(26) and Mackay(3) have also introduced advection (loss of the chemical from the troposphere via diffusion) and sedimentation (loss of the chemical from dynamic regions of the system by movement deep into sedimentation layers). Both of these mechanisms are then assumed to act in the unit world. This approach makes it possible to investigate the behavior of atmosphere emissions where advection can be a significant process. Therefore, from a regulatory standpoint if the emission rate exceeds the advection rate and degradation processes in a system, accumulation of material could be expected. Based on such an analysis reduction of emissions would be called for. 

Fig. 13. Breakdown into the contributing dissipation mechanisms of dry pressure drops in vessels containing Montz Bl-250.45 structured packings. Reprinted from Chemical Engineering Science, Vol. 58, Petre et al, Pressure Drop Through Structured Packings Breakdown Into the Contributing Mechanisms by CFD Modeling, pp. 163-177, Copyright (2003), with permission from Elsevier.

Whenever a mechanism dissipates mechanical energy as heat there exists an inverse mechanism by which heat can generate a mechanical fluctuation. There is always a connection between fluctuation and dissipation. 

Leggett, A. J. Quantum tunneling in the presence of an arbitrary linear dissipation mechanism, Phys.Rev.B, 30(1984), 1208-1218... 

The discussion begins below with an overview of proposed energy dissipation mechanisms that lead to friction. This is followed by brief discussions of phenomenological friction laws that describe the dependence of friction upon normal load and sliding velocity. The dependence of friction on the symmetry of the surfaces that are in contact is discussed later. 

As a final point, we note that typical surfaces are usually not crystalline but instead are covered by amorphous layers. These layers are much rougher at the atomic scale than the model crystalline surfaces that one would typically use for computational convenience or for fundamental research. The additional roughness at the microscopic level from disorder increases the friction between surfaces considerably, even when they are separated by a boundary lubricant.15 Flowever, no systematic studies have been performed to explore the effect of roughness on boundary-lubricated systems, and only a few attempts have been made to investigate dissipation mechanisms in the amorphous layers under sliding conditions from an atomistic point of view. 

Based on the discussion in earlier sections of this chapter, one may expect atomically flat incommensurate surfaces to be superlubric. Indeed the first suggestion that ultra-low friction may be possible was based on simulations of copper surfaces.6,7 Furthermore, the simulations of Ni(100)/(100) interfaces discussed in the previous section showed very low friction when the surfaces were atomically flat and misoriented (see the data for the atomically flat system between 30° and 60° in Figure 21). In general, however, it is reasonable to assume that bare metals are not good candidates for superlubric materials because they are vulnerable to a variety of energy dissipation mechanisms such as dislocation formation, plastic deformation, and wear. 

A major limitation of the dissipative mechanisms involving multiplicative noise —and by extension the iGLE and WiGLE models— is that they involve equilibrium changes only in the strength of the response with respect to the instantaneous friction kernel. They do not involve a change in the response time of the solvent at equilibrium limits. Presumably the response time also changes in some systems, and the inclusion of this variation is a necessary component of the minimal class of models for nonstationary stochastic dynamics. Plow this should be included, however, is an open problem which awaits an answer. 

The extension of the shock tube to the plasma region where particle collision s become infrequent and other dissipative mechanisms must be explored, opens an exciting area for study... 

---