Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Damping effects function

Damping Behavior of Silent Paint . The damping behavior of a typical "Silent Paint" composition, cross-polv(ethyl methacrylate)-inter-cross-poly(n-butyl acrylate) 25/75, constrained with epoxy resin, was then compared with several commercial materials as a function of temperature. Figure 3. The "Silent Paint" composition, curve A, damped effectively over a broad temperature range whereas the commercial materials, curves B and C [poly (vinyl acetate) ], and D, E, and F, of various compositions, damped effectively over narrower temperature ranges. [Pg.418]

Fig. 15. Polarization-transfer efficiency in a spin system consisting of three spins 1/2 under ideal isotropic-mixing conditions (effective ///-TOCSY coupling topology). (A) Damped transfer functions - t U12I) as a function of the relative coupling constant... Fig. 15. Polarization-transfer efficiency in a spin system consisting of three spins 1/2 under ideal isotropic-mixing conditions (effective ///-TOCSY coupling topology). (A) Damped transfer functions - t U12I) as a function of the relative coupling constant...
A more robust method involves preheating the air 10-20°C above ambient. This increases the low adsorptive capacity of the air and ensures that drying continues throughout winter. Less basic versions recycle the heated air within an enclosed space and in effect function as a uninsulated, low-temperature kiln. Such an operation has attractions where damp winters make air-drying very slow. They are cheap, and capital is often limited for small companies. Low-temperature, low-cost driers provide some control over the drying elements that is lacking in air-drying. [Pg.275]

As an example, it has been pointed out that the Hamaker and Lifshitz theories assume (exphcitly and implicitly, respectively) that intensive physical properties of the media involved such as density, and dielectric constant, remain unchanged throughout the phase—that is, right up to the interface between phases. We know, however, that at the atomic or molecular level solids and liquids (and gases under certain circumstances) exhibit short-range periodic fluctuations they are damped oscillating functions. Conceptually, if one visualizes a hquid in contact with a flat solid surface (Fig. 4.8a), one can see that the molecules (assumed to be approximately spherical, in this case) trapped between the surface and the bulk of the liquid will have less translational freedom relative to the bulk and therefore be more structured. That structure will (or may) result in changes in effective intensive properties near the surface. [Pg.72]

On the basis of Equation 4.25, the mixing time in microchannels with different diameters between 50 and 1000 pm was estimated to be a function of the specific power dissipation. Physical properties correspond to water at room temperature and atmospheric pressure. Because of the damping effect of the logarithmic function, the influence of the f e-number diminishes and the mixing time can be estimated with the simplified relation in Equation 4.26 (see Figure 4.13). [Pg.141]

Figure 2 shows the phase velocity as a function of the frequency of the sound field for three different values of void fraction ao and for an equilibrium radius of 20 m and y=0. The pipe factor is zero, which corresponds to a mixture flow without pipe walls. We see that for the case of resonance we have a very strong dependence of the phase velocity from the void fraction. The influence of the pipe factor on the pressure pulse velocity is plotted in Figure 3. The phase velocity is a function of the frequency of the sound field. We see that with increasing values of the pipe factor the phase velocity decreases. Figure 4 shows the influence of the void fraction and the frequency on the damping effect of the system. It may be noted that the imaginary part of the dispersion relation correspons to the damping of the pressure waves. Figure 4 shows the strong dependence of the damping parameter from the void fraction (see also [9]). Figure 2 shows the phase velocity as a function of the frequency of the sound field for three different values of void fraction ao and for an equilibrium radius of 20 m and y=0. The pipe factor is zero, which corresponds to a mixture flow without pipe walls. We see that for the case of resonance we have a very strong dependence of the phase velocity from the void fraction. The influence of the pipe factor on the pressure pulse velocity is plotted in Figure 3. The phase velocity is a function of the frequency of the sound field. We see that with increasing values of the pipe factor the phase velocity decreases. Figure 4 shows the influence of the void fraction and the frequency on the damping effect of the system. It may be noted that the imaginary part of the dispersion relation correspons to the damping of the pressure waves. Figure 4 shows the strong dependence of the damping parameter from the void fraction (see also [9]).
The power substation is of course the first main electrical component to be put into service since it is required to be functional during construction of the mine. In the present case, an interim power configuration was put into service to supply power to the production hoist. At that time, the 8000 HP Hoist Drive (ARU based front end) used for shaft sinking is than the main electrical load in service the damping effect normally resulting from other heavy electrical loads is not yet there. [Pg.157]

Fig. 21. Damping effectiveness as a function of temperature for several commercial materials compared to an IPN, composition A. Fig. 21. Damping effectiveness as a function of temperature for several commercial materials compared to an IPN, composition A.
Effects (functions) To clear heat and dry dampness, astringe to check dysentery, check vaginal discharge, and improve vision... [Pg.12]

Effects (functions) To dispers wind-cold, relieve the stuffy nose, dispel wind-dampness... [Pg.79]

Effects (functions) Cools heat, disinfects and detoxifies, Eczema, burns and unclerations, breaks up lumps, clears damp- heat, cools blood... [Pg.115]

Effects (functions) To dispel wind-dampness, clear dampness-heat, relieve impediment pain, relieve deficiency heat... [Pg.138]


See other pages where Damping effects function is mentioned: [Pg.243]    [Pg.507]    [Pg.188]    [Pg.507]    [Pg.159]    [Pg.273]    [Pg.114]    [Pg.83]    [Pg.31]    [Pg.102]    [Pg.2]    [Pg.363]    [Pg.323]    [Pg.328]    [Pg.124]    [Pg.266]    [Pg.157]    [Pg.204]    [Pg.326]    [Pg.388]    [Pg.297]    [Pg.79]    [Pg.625]    [Pg.82]    [Pg.363]    [Pg.248]    [Pg.2280]    [Pg.200]    [Pg.625]    [Pg.586]    [Pg.338]    [Pg.654]    [Pg.401]    [Pg.644]   
See also in sourсe #XX -- [ Pg.288 ]




SEARCH



Damping effective

Damping effects

Damping function

Effective functionality

Effects function

© 2024 chempedia.info