Copper, viii

Nelson et al. [34] determined from void shapes that the ratio 7100/7110 was 1.2, 0.98 and 1.14 for copper at 600°C, aluminum at 550°C, and molybdenum at 2000°C, respectively, and 1.03 for 7100/7111 for aluminum at 450°C. Metal tips in field emission studies (see Section VIII-2C) tend to take on an equilibrium faceting into shapes agreeing fairly well with calculations [133]. 

In the first method a secondary acetylenic bromide is warmed in THF with an equivalent amount of copper(I) cyanide. We found that a small amount of anhydrous lithium bromide is necessary to effect solubilization of the copper cyanide. Primary acetylenic bromides, RCECCH Br, under these conditions afford mainly the acetylenic nitriles, RCsCCHjCsN (see Chapter VIII). The aqueous procedure for the allenic nitriles is more attractive, in our opinion, because only a catalytic amount of copper cyanide is required the reaction of the acetylenic bromide with the KClV.CuCN complex is faster than the reaction with KCN. Excellent yields of allenic nitriles can be obtained if the potassium cyanide is added at a moderate rate during the reaction. Excess of KCN has to be avoided, as it causes resinifi-cation of the allenic nitrile. In the case of propargyl bromide 1,1-substitution may also occur, but the propargyl cyanide immediately isomerizes under the influence of the potassium cyanide. 

In the flask were placed 40 ml of ethanol, 10 ml of water, 12 g of finely powdered CuCN and 0.40 mol of 3-bromo-l-butyne (compare VIII-2, Exp. 3). The mixture was warmed to 55°C and a solution of 26 g of KCN in 60 ml of water was added drop-wise or in small portions care was taken that complete dissolution of the copper cyanide did not occur (note 2). The temperature of the mixture was maintained close to 60°C throughout the period of addition. The conversion was terminated... 

To a suspension of a tinc-copper couple in 150 ml of 100 ethanol, prepared from 80 g of zinc powder (see Chapter II, Exp. 18), was added at room temperature 0.10 mol of the acetylenic chloride (see Chapter VIII-2, Exp. 7). After a few minutes an exothermic reaction started and the temperature rose to 45-50°C (note 1). When this reaction had subsided, the mixture was cooled to 35-40°C and 0,40 mol of the chloride was added over a period of 15 min, while maintaining the temperature around 40°C (occasional cooling). After the addition stirring was continued for 30 min at 55°C, then the mixture was cooled to room temperature and the upper layer was decanted off. The black slurry of zinc was rinsed five times with 50-ml portions of diethyl ether. The alcoholic solution and the extracts were combined and washed three times with 100-ml portions of 2 N HCl, saturated with ammonium chloride. 

In the flask were placed 0.40 mol of dry, powdered copper(I) cyanide, 9 g of anhydrous lithium bromide (note 1), 50 ml of dry THF and 0.30 mol of l-bromo-2--heptyne (prepared from the corresponding alcohol and PBrs in diethyl ether, see VIII-2, Exp. 10). The mixture was heated until an exothermic reaction started, which occurred at about 80°C. The solid dissolved gradually. The mixture was kept... 

Hydrogenation Catalysts. The key to catalytic hydrogenation is the catalyst, which promotes a reaction which otherwise would occur too slowly to be useful. Catalysts for the hydrogenation of nitro compounds and nitriles are generally based on one or more of the group VIII metals. The metals most commonly used are cobalt, nickel, palladium, platinum, rhodium, and mthenium, but others, including copper (16), iron (17), and tellurium... 

The oxidation reaction between butadiene and oxygen and water in the presence of CO2 or SO2 produces 1,4-butenediol. The catalysts consist of iron acetylacetonate and LiOH (99). The same reaction was also observed at 90°C with Group (VIII) transition metals such as Pd in the presence of I2 or iodides (100). The butenediol can then be hydrogenated to butanediol [110-63-4]. In the presence of copper compounds and at pH 2, hydrogenation leads to furan (101). 

We plan to make studies on palladium-copper, iridium-copper, and platinum-copper catalysts to extend our investigation of the effect of varying miscibility of the components on the structural features of the bimetallic clusters present. With these additional systems, the whole range from complete immiscibility to total miscibility of copper with the Group VIII metal will be encompassed. 

VIII,5. COPPER PHTHALOCYANINE (MONASTRAL BLUE) The pure pigment may be obtained by heating phthalonitrile (4 mols) and copper bronze (1 atom) at 209-220 ... 

Pepper, John Henry. The playbook of metals including personal narratives of visits to coal, lead, copper, and tin mines with a large number of interesting experiments relating to alchemy and the chemistry of fifty metallic elements, by John Henry Pepper. With three hundred illustrations. New ed ed. London, New York Routledge, 1869. viii, 502 p. 

The dominant role of copper catalysts has been challenged by the introduction of powerful group VIII metal catalysts. From a systematic screening, palladium(II) and rhodium(II) derivatives, especially the respective carboxylates62)63)64-, have emerged as catalysts of choice. In addition, rhodium and ruthenium carbonyl clusters, Rh COJjg 65> and Ru3(CO)12 e6), seem to work well. Tables 3 and 4 present a comparison of the efficiency of different catalysts in cyclopropanation reactions with ethyl diazoacetate under standardized conditions. 

As it is known from experience that the metal carbenes operating in most catalyzed reactions of diazo compounds are electrophilic species, it comes as no surprise that only a few examples of efficient catalyzed cyclopropanation of electron-poor alkeiies exist. One of those examples is the copper-catalyzed cyclopropanation of methyl vinyl ketone with ethyl diazoacetate 140), contrasting with the 2-pyrazoline formation in the purely thermal reaction (for failures to obtain cyclopropanes by copper-catalyzed decomposition of diazoesters, see Table VIII in Ref. 6). 

Tolman (144, 202) and Wieghardt (203, 204) and their co-workers used amine macrocycles with a 1,4,7-triazacyclononane backbone and one, two, or three phenol pendent arms (Table VIII). In all cases, square-base pyramidal (phenolate)copper(II) precursor complexes were isolated and in many instances structurally characterized by X-ray crystallography. Depending on the number of coordinated phenolates, these complexes are reversibly one-electron oxidized yielding the (phenoxyl)copper(II) species that were characterized in solution by UV-vis, EPR, and RR spectroscopy. 

On the addition of copper acetate to a solution of compound (VI) the copper salt (VII) is formed which on treatment with acid decomposes to form 5-azido-tetrazole (VIII) ... 

---