Conducting electrolytic polymerization, mechanism

Noda and Watanabe [42] reported a simple synthetic procedure for the free radical polymerization of vinyl monomers to give conducting polymer electrolyte films. Direct polymerization in the ionic liquid gives transparent, mechanically strong and highly conductive polymer electrolyte films. This was the first time that ambient-temperature ionic liquids had been used as a medium for free radical polymerization of vinyl monomers. The ionic liquids [EMIM][BF4] and [BP][Bp4] (BP is N-butylpyridinium) were used with equimolar amounts of suitable monomers, and polymerization was initiated by prolonged heating (12 hours at 80 °C) with benzoyl... 

Polymeric electrolytes can possibly be used to build safe, non-toxic modern battery systems, e.g. Li-batteries. In this context the understanding of the ionic conduction mechanism of dissolved alkali salts is of major importance. Besides macroscopic measurements of transport coefficients, the investigation of mobilities on a molecular level is essential to identify the relevant conduction mechanisms. 

Ionically conducting polymers and their relevance to lithium batteries were mentioned in a previous section. However, there are several developments which contain both ionically conducting materials and other supporting agents which improve both the bulk conductivity of these materials and the properties of the anode (Li)/electrolyte interface in terms of resistivity, passivity, reversibility, and corrosion protection. A typical example is a composite electrolyte system comprised of polyethylene oxide, lithium salt, and A1203 particles dispersed in the polymeric matrices, as demonstrated by Peled et al. [182], By adding alumina particles, a new conduction mechanism is available, which involved surface conductivity of ions on and among the particles. This enhances considerably the overall conductivity of the composite electrolyte system. There are also a number of other reports that demonstrate the potential of these solid electrolyte systems [183],... 

Ion conducting polymers may be preferable in these devices electrolytes because of their flexibility, moldability, easy fabrication and chemical stability (for the same reasons that they have been applied to lithium secondary batteries [19,48,49]). The gel electrolyte systems, which consist of a polymeric matrix, organic solvent (plasticizer) and supporting electrolyte, show high ionic conductivity about 10 5 S cnr1 at ambient temperature and have sufficient mechanical strength [5,7,50,51], Therefore, the gel electrolyte systems are superior to solid polymer electrolytes and organic solvent-based electrolytes as batteries and capacitor materials for ambient temperature operation. 

Conductive polymers may be synthesized via either chemical or electrochemical polymerization methods. Electrodeposition of conductive polymers from electrolytes is, thus, feasible provided that the depositing polymer is not soluble in the electrolyte.206 Conductive polymers can be deposited from the electrolytes containing the monomers via either electrooxidation or electroreduction, based on the monomer type used. Similar to that of metals, the electrodeposition of polymers is based on nucleation and growth. The deposition mechanism involves oxidation of monomers adsorbed on the electrode surface, diffusion of the oxidized monomers and oligomerization, formation of clusters, and eventually film growth.213... 

Electrically conducting polymers are quite different systems to the above elec-troinitiated chain polymerizations since they are formed by an unusual step-growth mechanism involving stoichiometric transfer of electrons. The polymers are obtained directly in a conductive polycationic form in which charge-compensating counter anions from the electrolyte system are intercalated into the polymer matrix [173], Exact mechanistic details remain the subject of discussion, but Scheme 4, which shows polypyrrole formation is plausible. Polythiophene is similar where S replaces NH in the ring. 

Many approaches have been developed for the production of ionic liquid-polymer composite membranes. For example, Doyle et al. [165] prepared RTILs/PFSA composite membranes by swelling the Nafion with ionic liquids. When 1-butyl, 3-methyl imidazolium trifluoromethane sulfonate was used as the ionic liquid, the ionic conductivity ofthe composite membrane exceeded 0.1 S cm at 180 °C. A comparison between the ionic liquid-swollen membrane and the liquid itself indicated substantial proton mobility in these composites. Fuller et al. [166] prepared ionic liquid-polymer gel electrolytes by blending hydrophilic RTILs into a poly(vinylidene fiuoridej-hexafluoropropylene copolymer [PVdF(HFP)] matrix. The gel electrolytes prepared with an ionic liquid PVdF(HFP) mass ratio of 2 1 exhibited ionic conductivities >10 Scm at room temperature, and >10 Scm at 100 °C. When Noda and Watanabe [167] investigated the in situ polymerization of vinyl monomers in the RTILs, they produced suitable vinyl monomers that provided transparent, mechanically strong and highly conductive polymer electrolyte films. As an example, a 2-hydroxyethyl methacrylate network polymer in which BPBF4 was dissolved exhibited an ionic conductivity of 10 S cm at 30 °C. 

There are two types of polymeric electrolyte, based on their conduction mechanisms. The first group is the polyelectrolyte in which the polymer itself contains an anionic or cationic group, usually on a side chain. The counter-ions for these groups are typically small, inorganic ions that are mobile within the polymer matrix. Nafion, a perfluorinated sulfonated ionomer made by du Pont, is an example of this type of electrolyte [1]. Nafion has been used as the electrolyte in several amperometric gas sensors. 

---