Composites dispersed phases

Drilling fluids are classified as to the nature of the continuous phase gas, water, oil, or synthetic. Within each classification are divisions based on composition or chemistry of the fluid or the dispersed phase. 

Colloidal State. The principal outcome of many of the composition studies has been the delineation of the asphalt system as a colloidal system at ambient or normal service conditions. This particular concept was proposed in 1924 and described the system as an oil medium in which the asphaltene fraction was dispersed. The transition from a coUoid to a Newtonian Hquid is dependent on temperature, hardness, shear rate, chemical nature, etc. At normal service temperatures asphalt is viscoelastic, and viscous at higher temperatures. The disperse phase is a micelle composed of the molecular species that make up the asphaltenes and the higher molecular weight aromatic components of the petrolenes or the maltenes (ie, the nonasphaltene components). Complete peptization of the micelle seems probable if the system contains sufficient aromatic constituents, in relation to the concentration of asphaltenes, to allow the asphaltenes to remain in the dispersed phase. 

Flow behavior of the polymer blends is determined by their structure, which is governed by the degree of dispersion of the component and by the mode of their distribution. For blends having identical compositions, it is possible to produce systems in which one and the same component may be either a dispersion medium or a dispersed phase [1]. This behavior of the polyblend systems depends on various parameters, the most important of which is the blending sequence. It is, therefore, difficult to obtain a uniform composition property relationship for the polymer blends even though the composition remains identical. 

According to the criteria, the dispersed phase embedded in the matrix of sample 1 must have been deformed to a maximum aspect ratio and just began or have begun to break up. By observing the relative position of the experimental data to the critical curve, the deformational behavior of the other samples can be easily evaluated. Concerning the fibrillation behavior of the PC-TLCP composite studied, the Taylor-Cox criteria seems to be valid. 

Stability may be inherent or induced. In the latter case, the original system is in a condition of metastable or neutral eouilibrium. External influences which induce instability in a dispersion on standing are changes in temperature, volume, concentration, chemical composition, and sediment volume. Applied external influences consist of shear, introduction of a third component, and compaction of the sediment. Interfacial energy between solid and liquid must be minimized, if a dispersion is to be truly stable. Two complementary stabilizing techniques are ionic and steric protection of the dispersed phase. The most fruitful approach to the prediction of physical stability is by electrical methods. Sediment volumes bear a close relation to repulsion of particles for each other. 

In interfacial polymerization, monomers react at the interface of two immiscible liquid phases to produce a film that encapsulates the dispersed phase. The process involves an initial emulsification step in which an aqueous phase, containing a reactive monomer and a core material, is dispersed in a nonaqueous continuous phase. This is then followed by the addition of a second monomer to the continuous phase. Monomers in the two phases then diffuse and polymerize at the interface to form a thin film. The degree of polymerization depends on the concentration of monomers, the temperature of the system, and the composition of the liquid phases. 

For these various reasons one may ask if it is possible to develop automated or semi-automated methods that will simultaneously measure compositions and other thermodynamic parameters at reservoir pressures and temperatures, without waiting for bulk separation of dispersed phases in the apparatus. 

The melt mixed 80/20 PS/iPP blend displays a set of exotherms, where the amount of the iPP component that was heterogeneously nucleated is substantially reduced as indicated by the decrease of the crystallization enthalpy in the temperature region where the iPP crystallizes in bulk, i.e., at 109-111 °C (exotherm labeled A). This effect is due to the confinement of iPP into a large number of droplets. If the number of droplets of iPP as a dispersed phase is greater than the number of heterogeneities present in the system, fractionated crystallization occurs. The number of droplets for this composition is known (by scanning electron microscopy observations) to be of the order of 1011 particles cm-3 and polarized optical microscopy (POM) experiments have shown that this iPP contains approximately 9 x 106 heterogeneities cm-3. In fact, it can be seen in Fig. 1 that the fractionated crystallization of the iPP compon-... 

In this level, the fundamental tasks required to convert the raw materials into the final product are identified. All tasks are related to property differences. Siirola (1996) has presented the following hierarchy of property differences molecular identity, amount, composition, phase, temperature/pressure, form. This list of tasks is not very well suited for food properties. Common tasks for food processes are decontamination (e.g. pasteurization and sterilization) and structure formation (e.g. emulsification, size reduction of dispersed phase in an emulsion, crystallization, interfacial adsorption/desorption). 

Various zeolites have been studied as the dispersed phase in the mixed-matrix membranes. Zeolite performance in the zeolite/polymer mixed-matrix membrane is determined by several key characteristics including pore size, pore dimension, framework structure, chemical composition (e.g., Si/Al ratio and cations), crystal morphology and crystal (or particle) size. These characteristics of zeolites are summarized in Chapter 6. 

Manson (72,) expanded the concept to the solid state by observing that the strength of composite materials also depended upon the acid-base interaction between continuous and dispersed phases. More directly, Vanderhoff et al. (21) addressed the issue of adhesion of polymeric materials to corroded steel. They synthesized eight corrosion products of iron, and used the interaction scheme developed by Fowkes and Manson first to characterize the iron corrosion products as Lewis acids or bases and then to select polymer vehicles for practical coating systems. Such results were employed to enhance the adhesion of epoxy systems to substrates which were predominantly iron oxide in nature. A good overview of these Issues was presented by Fowkes in 1983 (74). ... 

Yeo, et al. [23,24] went on to make more complete studies of modulus-composition data using cross-poly(n-butyl acrylate)-Inter-cross-polystyrene, PnBA/PS, see Figure 6. Both the Davies and the Budlansky models fit reasonably well over wide ranges of composition, especially the Budlansky model. Other models, which in one form or another assume one continuous and one disperse phase, fit much less well. 

It is the intent of this doeument to define the terms most commonly encountered in the field of polymer blends and eomposites. The scope has been limited to mixtures in which the eomponents differ in ehemical composition or molar mass or both and in which the continuous phase is polymeric. Many of the materials described by the term multiphase are two-phase systems that may show a multitude of finely dispersed phase domains. Hence, incidental thermodynamic descriptions are mainly limited to binary mixtures, although they can be and, in the scientific literature, have been generalized to multicomponent mixtures. Crystalline polymers and liquid-crystal polymers have been considered in other documents [1,2] and are not discussed here. 

---