Butyl bromide reaction

The methyl bromide reaction is said to follow second-order kinetics, since its rate is dependent upon the concentrations of two substances. The rer/-butyl bromide reaction is said to follow first-order kinetics its rate depends upon the concentration of only one substance. 

How are we to account for this difference in kinetic order How are we to account for the puzzling fact that the rate of the /er/-butyl bromide reaction is independent of [OH"] ... 

The preparation of -butyl bromide as an example of ester formation by Method 1 (p. 95) has certain advantages over the above preparation of ethyl bromide. -Butanol is free from Excise restrictions, and the -butyl bromide is of course less volatile. and therefore more readily manipulated without loss than ethyl bromide furthermore, the n-butyl bromide boils ca. 40° below -butyl ether, and traces of the latter formed in the reaction can therefore be readily eliminated by fractional distillation. 

To a solution of 0.30 mol of ethyllithium (note 1) in about 270 ml of diethyl ether (see Chapter II, Exp. 1) v/as added 0.30 mol of methoxyallene at -20°C (see Chapter IV, Exp. 4) at a rate such that the temperature could be kept between -15 and -2Q°C. Fifteen minutes later a mixture of 0.27 mol of >z-butyl bromide and 100 ml of pure, dry HMPT ivas added in 5 min with efficient cooling, so that the temperature of the reaction mixture remained below 0°C. The cooling bath was then removed and the temperature was allowed to rise. After 4 h the brown reaction mixture was poured into 200 ml of ice-water. The aqueous layer was extracted twice with diethyl ether. The combined solutions were washed with concentrated ammonium chloride solution (which had been made slightly alkaline by addition of a few millilitres of aqueous ammonia, note 2) and dried over potassium carbonate. After addition of a small amount (2-5 ml) of... 

To a mixture of 0.10 mol of 1-ethoxy-l,2-heptadiene (see this chapter, Exp. 13) and 120 ml of diethyl ether was added 1 g of copper(I) bromide. A solution of butyl magnesium bromide in about 200 ml of diethyl ether, prepared from 0.25 mol of butyl bromide (see Chapter II, Exp. 5) was added in 15 min. The reaction was weakly exothermic and the temperature rose slowly to about 32°C. The mixture was held for an additional 40 min at that temperature, then the black reaction mixture was... 

Sodium cyanide does not dissolve m butyl bromide The two reactants contact each other only at the surface of the solid sodium cyanide and the rate of reaction under these con ditions IS too slow to be of synthetic value Dissolving the sodium cyanide m water is of little help because butyl bromide is not soluble m water and reaction can occur only at the interface between the two phases Adding a small amount of benzyltrimethyl ammonium chlonde however causes pentanemtnle to form rapidly even at room temper ature The quaternary ammonium salt is acting as a catalyst it increases the reaction rate How7... 

Phase transfer catalysis has been used with success to prepare N- substituted pyrazoles (78MI40403, 79MI40408, 70JHC1237, 80JOC3172) and this procedure can be considered the simplest and most efficient way to obtain these compounds. Experimental design methodology has been used to study the influence of the factors on the reaction between pyrazole and -butyl bromide under phase transfer conditions (79MI40408). 

In a 5-I. round-bottom flask, fitted with a stirrer, separatory funnel and a reflux condenser to the upper end of which a calcium chloride tube is attached, is placed 150 g. of magnesium turnings. A small crystal of iodine (Note i) and about 100 cc, of a mixture of 822 g. (6 moles) of M-butyl bromide and 2 1. of anhydrous ethyl ether are added. As soon as the reaction starts, 350 cc. of anhydrous ether is added and the remainder of the -butyl bromide solution is dropped in at such a rate that the mixture boils continuously. The time of addition (one and one-half hours) may be decreased by cooling the flask externally. Stirring is started as soon as enough liquid is present in the flask. 

I. The reaction between the ethereal solution of butyl bromide and the magnesium frequently starts without any assistance, but the presence of a trace of iodine is of no disadvantage and renders more certain the beginning of the reaction. 

The butyl bromide appears to react as fast as it is added, so that there is no need of stirring or warming the butylmag-nesium bromide solution before adding the ethylene oxide. The small amount of unattacked magnesium has no influence on the subsequent reactions. 

Neopentyl (2,2-dimethylpropyl) systems are resistant to nucleo diilic substitution reactions. They are primary and do not form caibocation intermediates, but the /-butyl substituent efiTectively hinders back-side attack. The rate of reaction of neopent>i bromide with iodide ion is 470 times slower than that of n-butyl bromide. Usually, tiie ner rentyl system reacts with rearrangement to the /-pentyl system, aldiough use of good nucleophiles in polar aprotic solvents permits direct displacement to occur. Entry 2 shows that such a reaction with azide ion as the nucleophile proceeds with complete inversion of configuration. The primary beiuyl system in entry 3 exhibits high, but not complete, inversiotL This is attributed to racemization of the reactant by ionization and internal return. 

The real world of Sn reactions is not quite as simple as the discussion has so far suggested. The preceding treatment in terms of two clearly distinct mechanisms, SnI and Sn2, implies that all substitution reactions will follow one or the other of these mechanisms. This is an oversimplification. The strength of the dual mechanism hypothesis and its limitations are revealed by these relative rates of solvolysis of alkyl bromides in 80% ethanol methyl bromide, 2.51 ethyl bromide, 1.00 isopropyl bromide, 1.70 /er/-butyl bromide, 8600. Addition of lyate ions increases the rate for the methyl, ethyl, and isopropyl bromides, whereas the tert-butyl bromide solvolysis rate is unchanged. The reaction with lyate ions is overall second-order for methyl and ethyl, first-order for tert-butyl, and first- or second-order for the isopropyl member, depending upon the concentrations. Similar results are found in other solvents. These data show that the methyl and ethyl bromides solvolyze by the Sn2 mechanism, and tert-butyl bromide by the SnI mech-... 

The chiral center in 2-butyl bromide is created when Br adds to 2-butyl cation. The key, then, is to predict the enantioselectivity of this step. 2-Butyl cation exists as a mixture of three conformers planar, perpendicular A, and perpendicular B. Compare their energies and use equation (1) to calculate the relative amounts of each conformer at 298 K. Should all three conformers participate in the reaction to a significant extent ... 

Finally, use the relative amounts of the different cation conformers along with the reactivity preference of each conformer to determine the overall enantioselectivity of the addition reaction. Do you expect more R or S 2-butyl bromide to form Explain how you arrived at this answer. 

---