Boiling solvent methods

Esters. General, high-boiling solvent method. 

Although the boiling-point method is able to dispose of a greater numbei of convenient solvents than are suitable for freezing-point determinations, it is never so accurate, mainly on account of the difficulty of avoiding fluctuations in the boiling-point, due to radiation, to the dripping of cold liquid from the condenser, to impure solvent, and to barometric fluctuations. 

Bis ( -arene) metal complexes have been made for many transition metals by the AI/AICI3 reduction method and cationic species [M( j -Ar)2]"" " are also well established for n = 1, 2, and 3. Numerous arenas besides benzene have been used, the next most common being l,3,5-Mc3C6H3 (mesitylene) and CeMce. Reaction of arenas with metal carbonyls in high-boiling solvents or under the influence of ultraviolet light results in the displacement of 3CO and the formation of arena-metal carbonyls ... 

The most reliable method of preparing benzofuroxans is by decomposition of o-nitrophenyl azides. Decomposition can be achieved by irradiation, or more usually by pyrolysis temperatures between 100° and 1.50° are commonly used. Refluxing in glacial acetic acid is the recommended procedure for 4- or 5-sub-stituted 2-nitrophenyl azides, but with 3- or 6-substituted compounds higher boiling solvents are usually necessary. Quantitative studies on the reaction rate have been made, and a cyclic transition state invoked, an argument which has been used to account for the greater difficulty of decomposition of the 6-substituted 2-nitrophenyl azides. Substituent effects on the reaction rate have also been correlated with Hammett a constants, ... 

Since the products often precipitate during the polymerization, a modification was reported by Swatos et al. [82] involving the use of only about one equivalent of f-BuOK. This method, the so-called chlorine precursor route , first gives a soluble non-conjugated precursor (66) which is then converted thermally in the film or in a high boiling solvent, e.g. cyclohexanone. In the latter case, homogeneous solutions of (soluble) PPV derivatives 63 can be obtained. 

The traditional and most extensively used method of synthesis of chlorocyclophosphazenes [NPCl2] involves the reaction of finely ground ammonium chloride with phosphorus pentachloride in a high boiling solvent such as sym-tetrachloroethane. This reaction affords a mixture of cyclic and linear products from which the individual products have to be separated, usually by fractional distillation in high vacuum (1, 5,17,18,35-39), (Eq. 1) ... 

The classical methods of solvent extraction of polymers can be conveniently divided into those for which heat is required (Soxhlet/Soxtec ), and those methods for which no heat is added, but which utilise some form of agitation, i.e. shaking or sonication (Table 3.3). Other LSE procedures consist in soaking the polymer in boiling solvents [84,85] and cold LSE [80,86]. These methods are also time-consuming, use large amounts of solvents which are scheduled to be restricted in the future, and exhibit other limitations when analytes are present in small quantities, where they may actually be lost in concentration steps following extraction. Many norms are still based on such standard procedures [87,88],... 

For the extraction of rubber and rubber compounds a wide variety of solvents (ethyl acetate, acetone, toluene, chloroform, carbon tetrachloride, hexane) have been used [149]. Soxtec extraction has also been used for HDPE/(Tinuvin 770, Chimassorb 944) [114] and has been compared to ultrasonic extraction, room temperature diffusion, dissolution/precipitation and reflux extraction. The relatively poor performance of the Soxtec extraction (50% after 4h in DCM) as compared with the reflux extraction (95% after 2-4 h in toluene at 60 °C) was described to the large difference in temperature between the boiling solvents. Soxtec was also used to extract oil finish from synthetic polymer yam (calibration set range of 0.18-0.33 %, standard error 0.015 %) as reference data for NIRS method development [150]. 

Perylenes (70) are diimides of perylene-3,4,9,10-tetracarboxylic acid, and may be prepared by reaction of the bis-anhydride of this acid, 89 (1 mol) with the appropriate amine (2 mol) in a high-boiling solvent as illustrated in Scheme 4.11. The synthesis of perinones 71 and 72 involves condensation of naphthalene-1,4,5,8-tetracarboxylic acid with benzene-1,2-diamine in refluxing acetic acid. This affords a mixture of the two isomers, which may be separated by a variety of methods, generally involving their differential solubility in acids and alkalis. 

The solution to this difficulty, discovered by Schmid of Ciba in the early 1950s, is to reverse the order of the two steps. The diazotised amine is first coupled with BON acid and then two moles of this intermediate are condensed with one mole of benzidine in the form of its hydrochloride. The condensation is carried out in a high-boiling solvent such as nitrobenzene, when yields of 95% can be attained. These pigments have been called azo condensation pigments in view of their method of synthesis. 

The study of the properties and applications of clusters requires them to be accessible on a preparative scale and this is often conditioned by the ease with which they can be separated from other reaction products. Because their molecular weights are not too high, several tetranuclear clusters are volatile and/or soluble in organic solvents, and therefore the first methods of separation to be considered are sublimation under high vacuum (if the compound is thermally stable) and crystallization. When the solubility is low, continuous extraction with low boiling solvents can be tried50. ... 

The solvent process involves treating phthalonitrile with any one of a number of copper salts in the presence of a solvent at 120 to 220°C [10]. Copper(I)chloride is most important. The list of suitable solvents is headed by those with a boiling point above 180°C, such as trichlorobenzene, nitrobenzene, naphthalene, and kerosene. A metallic catalyst such as molybdenum oxide or ammonium molybdate may be added to enhance the yield, to shorten the reaction time, and to reduce the necessary temperature. Other suitable catalysts are carbonyl compounds of molybdenum, titanium, or iron. The process may be accelerated by adding ammonia, urea, or tertiary organic bases such as pyridine or quinoline. As a result of improved temperature maintenance and better reaction control, the solvent method affords yields of 95% and more, even on a commercial scale. There is a certain disadvantage to the fact that the solvent reaction requires considerably more time than dry methods. 

The customary method of preparing perylene pigments is by reaction of perylene tetracarboxylic dianhydride with primary aliphatic or aromatic amines in a high boiling solvent. The dianhydride itself is also used as a pigment. Di-methylperylimide may also be obtained by treating the diimide with methyl chloride or dimethyl sulfate. 

The first five measure the activity of the solvent and the last five measure the activity of the solute. The boiling point method is generally not included in evaluations for two reasons there are little data from these measurements or the thermal data are not adequate to apply an accurate correction to obtain an activity at 298 K. 

The resulting styrene/maleic acid copolymer is soluble in hot water, in contrast to the starting material the aqueous solution of the product gives a distinctly acid reaction. The disappearance of the anhydride moiety can be verified by IR or C-NMR spectroscopic methods.The IR spectra of polymers should be recorded from a film of the sample prepared on a KBr pellet (freshly made from KBr powder). For this, a drop of a solution of the polymer in a low-boiling solvent (e.g.,THF, methylene chloride) is placed on the pellet.The residual solvent can often be removed directly in the IR beam.The resulting spectra are characterized by their sharp bands. 

This method involves the thermolysis of organometallic or metal organic precursors in a high-boiling solvent. Mostly this solvent is also a capping agent for the nanoparticles. A typical synthetic route for monodisperse nanoparticles is shown in Fig. 1. 

---