Aromatics, catalytic cracking

The gas oil cut from catalytic cracking called Light Cycle Oil (LCO), is characterized by a very low cetane number (about 20), high contents in aromatics, sulfur and nitrogen, all of which strongly limit its addition to the diesel fuel pool to a maximum of 5 to 10%. 

Products of conversion from catalytic cracking are largely olefinic for light fractions and strongly aromatic for the heavy fractions. 

For gas oil from catalytic cracking (LCO), reducing the aromatics content to 20 wt. % results in a chemical hydrogen consumption of 3.4 wt % and a cetane number of 40. 

Furthermore, the major problem of reducing aromatics is focused around gasoline production. Catalytic reforming could decrease in capacity and severity. Catalytic cracking will have to be oriented towards light olefins production. Etherification, alkylation and oligomerization units will undergo capacity increases. 

Catalysis. As of mid-1995, zeoHte-based catalysts are employed in catalytic cracking, hydrocracking, isomerization of paraffins and substituted aromatics, disproportionation and alkylation of aromatics, dewaxing of distillate fuels and lube basestocks, and in a process for converting methanol to hydrocarbons (54). 

As is indicated in Figure 4, saturates contribute less to the vacuum gas oil (VGO) than the aromatics, but more than the polars present at percentage, rather than trace, levels. VGO itself is occasionally used as a heating oil but most commonly it is processed by catalytic cracking to produce naphtha or by extraction to yield lubricant oils. 

Deep C t lytic Crocking. This process is a variation of fluid catalytic cracking. It uses heavy petroleum fractions, such as heavy vacuum gas oil, to produce propylene- and butylene-rich gaseous products and an aromatic-rich Hquid product. The Hquid product contains predorninantiy ben2ene, toluene, and xylene (see BTX processing). This process is being developed by SINOPEC in China (42,73). SINOPEC is currentiy converting one of its fluid catalytic units into a demonstration unit with a capacity of 60,000 t/yr of vacuum gas oil feedstock. 

Acid-treated clays were the first catalysts used in catalytic cracking processes, but have been replaced by synthetic amorphous silica-alumina, which is more active and stable. Incorporating zeolites (crystalline alumina-silica) with the silica/alumina catalyst improves selectivity towards aromatics. These catalysts have both Fewis and Bronsted acid sites that promote carbonium ion formation. An important structural feature of zeolites is the presence of holes in the crystal lattice, which are formed by the silica-alumina tetrahedra. Each tetrahedron is made of four oxygen anions with either an aluminum or a silicon cation in the center. Each oxygen anion with a -2 oxidation state is shared between either two silicon, two aluminum, or an aluminum and a silicon cation. 

It has been shown, however, that such catalysts may contain protons, either by design or because of the difficulty in removing all traces of moisture, and these protons have been shown to be superacidic with Hammett acidities up to —18. These protons will also play some role in the catalytic activity of these ionic liquids in practical situations. Ionic liquids in which superacidic protons have deliberately been generated by addition of small amounts of water, HCl or H2SO4 have been used to catalytically crack polyethene under relatively mild conditions. The main products are mixed C3-C5 alkanes, which would be a useful feedstock from waste polyethene recycling. In contrast to other cracking procedures no aromatics or alkenes are produced, although small amounts of polycyclic compounds are obtained. 

The benefits related to the particular topology of ITQ-21 when used as heterogeneous catalyst have been reported for different processes, such as catalytic cracking [1], hydrocracking [2] or hidrogenation and ring opening of (poly)aromatics [3]... 

Most of the commercial zeolite catalyzed processes occur either through acid catalysis fluid catalytic cracking (FCC), aromatic alkylation, methanol to olefins (MTO),... 

Catalytic cracking occurs at about 800°K (527°C, 980°F) and at these temperatures the formation of olefins and aromatics is favored while isomerization of paraffins to branched products is... 

---