An elastic solid

Let a solid body occupy the domain fl C with the smooth boundary T. The solid particle coincides with the point x = xi,X2,xs) G fl. An elastic solid is described by the following functions ... 

A parameter indicating whether viscoelastic effects are important is the Deborah number, which is the ratio of the characteristic relaxation time of the fluid to the characteristic time scale of the flow. For small Deborah numbers, the relaxation is fast compared to the characteristic time of the flow, and the fluid behavior is purely viscous. For veiy large Deborah numbers, the behavior closely resembles that of an elastic solid. 

Elastic modulus Up to the fracture stress, glass behaves, for most practical purposes, as an elastic solid at ordinary temperatures. Most silicate-based commercial glasses display an elastic modulus of about 70GNm", i.e. about 1/3 the value for steel. If stress is applied at temperatures near the annealing range, then delayed elastic effects will be observed and viscous flow may lead to permanent deformation. 

A real material whose behaviour can be modelled in this way initially undergoes irreversible deformation as the stress is applied. This eventually ceases, and the material then behaves effectively as an elastic solid. Release of the stress will cause a rapid return to a less strained state, corresponding to the spring component of the response, but part of the deformation, arising due to viscous flow in the dashpot will not disappear. 

The rheological characteristics of AB cements are complex. Mostly, the unset cement paste behaves as a plastic or plastoelastic body, rather than as a Newtonian or viscoelastic substance. In other words, it does not flow unless the applied stress exceeds a certain value known as the yield point. Below the yield point a plastoelastic body behaves as an elastic solid and above the yield point it behaves as a viscoelastic one (Andrade, 1947). This makes a mathematical treatment complicated, and although the theories of viscoelasticity are well developed, as are those of an ideal plastic (Bingham body), plastoelasticity has received much less attention. In many AB cements, yield stress appears to be more important than viscosity in determining the stiffness of a paste. 

In the molten state polymers are viscoelastic that is they exhibit properties that are a combination of viscous and elastic components. The viscoelastic properties of molten polymers are non-Newtonian, i.e., their measured properties change as a function of the rate at which they are probed. (We discussed the non-Newtonian behavior of molten polymers in Chapter 6.) Thus, if we wait long enough, a lump of molten polyethylene will spread out under its own weight, i.e., it behaves as a viscous liquid under conditions of slow flow. However, if we take the same lump of molten polymer and throw it against a solid surface it will bounce, i.e., it behaves as an elastic solid under conditions of high speed deformation. As a molten polymer cools, the thermal agitation of its molecules decreases, which reduces its free volume. The net result is an increase in its viscosity, while the elastic component of its behavior becomes more prominent. At some temperature it ceases to behave primarily as a viscous liquid and takes on the properties of a rubbery amorphous solid. There is no well defined demarcation between a polymer in its molten and rubbery amorphous states. 

Murnaghan, F. D. "Finite Deformation of an Elastic Solid" Dover Publications, Inc. New York, 1967. 

The function iKt-t ) may be interpreted as a memory function having a form as shown in Figure 3.14. For an elastic solid, iff has the value unity at all times, while for a purely viscous liquid iff has the value unity at thfe current time but zero at all other times. Thus, a solid behaves as if it remembers the whole of its deformation history, while a purely viscous liquid responds only to its instantaneous deformation rate and is uninfluenced by its history. The viscoelastic fluid is intermediate, behaving as if it had a memory that fades exponentially with time. The purely elastic solid and the purely viscous fluid are just extreme cases of viscoelastic behaviour. 

Most pigmented systems are considered viscoelastic. At low shear rates and slow deformation, these systems are largely viscous. As the rate of deformation or shear rate increases, however, the viscous response cannot keep up, and the elasticity of the material increases. There is a certain amount of emphasis on viscoelastic behavior in connection with pigment dispersion as well as ink transportation and transformation processes in high-speed printing machines (see below). Under periodic strain, a viscoelastic material will behave as an elastic solid if the time scale of the experiment approaches the time required for the system to respond, i.e., the relaxation time. Elastic response can be visualized as a failure of the material to flow quickly enough to keep up with extremely short and fast stress/strain periods. 

We can see that as the stress is applied the strain increases up to a time t = t. Once the stress is removed we see complete recovery of the strain. All the strain stored has been recovered. The material has the properties of an elastic solid. In order to achieve viscous flow we need to include an additional term, the viscous loss term. This is known as a Burger Body ... 

When the helix amount increases the medium changes from a viscous liquid (sol) to an elastic solid (gel). The kinetics of gelation depends strongly on the quenching temperature. The rheological measurements that we performed are particularly focused on the sol-gel transition and on the definition of the "gel point". The greatest difficulty encountered is due to the weakness of the bonds which can easily be destroyed by the mechanical stress. 

Deformation of an elastic solid through which a mass point of the solid with co-ordinates Xi, X2, X-i in the undeformed state moves to a point with co-ordinates xi, X2, X3 in the deformed state and the deformation is defined by... 

Tensor whose components are deformation gradients in an elastic solid. 

Strain tensor for an elastic solid, whose elements are... 

Note 3 The deformation gradient tensor for the simple shear of an elastic solid is... 

Note 1 For an elastic solid, the constitutive equation may be written... 

---