Ammonium salts, carboxylate

Ethers, esters, ketones, and alcohols OrganophoBithoruB compounds Amines and quaternary ammonium salts Carboxylic adds Chelating agents Ion exchange... 

Note. Useful information can often be obtained by adding (i) dilute H,SO or (ii) dilute NaOH solution to an aqueous solution of the substance under investigation. A precipitate with (i) usually indicates an aromatic carboxylic acid from a metallic or from an ammonium salt. A precipitate or oil with (ii) usually indicates an aromatic amine from an amine salt. 

When an alkyl aryl ketone is heated with yellow ammonium polysulphide solution at an elevated temperature, an aryl substituted aliphatic acid amide is foimed the product actually isolated is the amide of the ci-aryl carboxylic acid together with a smaller amount of the corresponding ammonium salt of the oarboxylio acid. Thus acetophenone affords phenylacetamide (50 per cent.) and ammonium phenylacetate (13 per cent.) ... 

Salt Formation. Salt-forming reactions of adipic acid are those typical of carboxylic acids. Alkali metal salts and ammonium salts are water soluble alkaline earth metal salts have limited solubiUty (see Table 5). Salt formation with amines and diamines is discussed in the next section. 

Flotation reagents are used in the froth flotation process to (/) enhance hydrophobicity, (2) control selectivity, (J) enhance recovery and grade, and (4) affect the velocity (kinetics) of the separation process. These chemicals are classified based on utili2ation collector, frother, auxiUary reagent, or based on reagent chemistry polar, nonpolar, and anionic, cationic, nonionic, and amphoteric. The active groups of the reagent molecules are typically carboxylates, xanthates, sulfates or sulfonates, and ammonium salts. 

These association reactions can be controlled. Acetone or acetonylacetone added to the solution of the polymeric electron acceptor prevents insolubilization, which takes place immediately upon the removal of the ketone. A second method of insolubiUzation control consists of blocking the carboxyl groups with inorganic cations, ie, the formation of the sodium or ammonium salt of poly(acryhc acid). Mixtures of poly(ethylene oxide) solutions with solutions of such salts can be precipitated by acidification. 

New efficient vulcanization systems have been introduced in the market based on quaternary ammonium salts initially developed in Italy (29—33) and later adopted in Japan (34) to vulcanize epoxy/carboxyl cure sites. They have been found effective in chlorine containing ACM dual cure site with carboxyl monomer (43). This accelerator system together with a retarder (or scorch inhibitor) based on stearic acid (43) and/or guanidine (29—33) can eliminate post-curing. More recently (47,48), in the United States a proprietary vulcanization package based on zinc diethyldithiocarbamate [14324-55-1]... 

The isocyanurate reaction occurs when three equivalents of isocyanate react to form a six-membered ring, as shown in the fifth item of Fig. 1. Isocyanurate linkages are usually more stable than urethane linkages. Model compound studies show no degradation of the trimer of phenyl isocyanate below 270°C [10,11]. Catalysts are usually needed to form the isocyanurate bond. Alkali metals of carboxylic acids, such as potassium acetate, various quaternary ammonium salts, and even potassium or sodium hydroxide, are most commonly used as catalysts for the isocyanurate reaction. However, many others will work as well [12]. 

Low surface energy substrates, such as polyethylene or polypropylene, are generally difficult to bond with adhesives. However, cyanoacrylate-based adhesives can be effectively utilized to bond polyolefins with the use of the proper primer/activa-tor on the surface. Primer materials include tertiary aliphatic and aromatic amines, trialkyl ammonium carboxylate salts, tetraalkyl ammonium salts, phosphines, and organometallic compounds, which are initiators for alkyl cyanoacrylate polymerization [33-36]. The primer is applied as a dilute solution to the polyolefin surface, solvent is allowed to evaporate, and the specimens are assembled with a small amount of the adhesive. With the use of primers, adhesive strength can be so strong that substrate failure occurs during the course of the shear tests, as shown in Fig. 11. 

The most common method of resolution uses an acid-base reaction between a racemic mixture of chiral carboxylic acids (RC02H) and an amine base (RNH2) to yield an ammonium salt. 

The synthesis of key intermediate 12, in optically active form, commences with the resolution of racemic trans-2,3-epoxybutyric acid (27), a substance readily obtained by epoxidation of crotonic acid (26) (see Scheme 5). Treatment of racemic 27 with enantio-merically pure (S)-(-)-1 -a-napthylethylamine affords a 1 1 mixture of diastereomeric ammonium salts which can be resolved by recrystallization from absolute ethanol. Acidification of the resolved diastereomeric ammonium salts with methanesulfonic acid and extraction furnishes both epoxy acid enantiomers in eantiomerically pure form. Because the optical rotation and absolute configuration of one of the antipodes was known, the identity of enantiomerically pure epoxy acid, (+)-27, with the absolute configuration required for a synthesis of erythronolide B, could be confirmed. Sequential treatment of (+)-27 with ethyl chloroformate, excess sodium boro-hydride, and 2-methoxypropene with a trace of phosphorous oxychloride affords protected intermediate 28 in an overall yield of 76%. The action of ethyl chloroformate on carboxylic acid (+)-27 affords a mixed carbonic anhydride which is subsequently reduced by sodium borohydride to a primary alcohol. Protection of the primary hydroxyl group in the form of a mixed ketal is achieved easily with 2-methoxypropene and a catalytic amount of phosphorous oxychloride. 

The use of HMDS (ca. 1.5 mmol) and saccharin (0.01 mmol) per mmol of substrate in refluxing dichloromethane or chloroform has been recommended (5) for easy silylation of carboxylic acids, including azetidin-2-one-4-carboxyIic acids. Clear solutions result, i.e., no ammonium salts are present at completion of the reaction, and consequently the silyl esters can be obtained by direct distillation, or merely by evaporation of solvent. 

Trimerization to isocyanurates (Scheme 4.14) is commonly used as a method for modifying the physical properties of both raw materials and polymeric products. For example, trimerization of aliphatic isocyanates is used to increase monomer functionality and reduce volatility (Section 4.2.2). This is especially important in raw materials for coatings applications where higher functionality is needed for crosslinking and decreased volatility is essential to reduce VOCs. Another application is rigid isocyanurate foams for insulation and structural support (Section 4.1.1) where trimerization is utilized to increase thermal stability and reduce combustibility and smoke formation. Effective trimer catalysts include potassium salts of carboxylic acids and quaternary ammonium salts for aliphatic isocyanates and Mannich bases for aromatic isocyanates. 

The mechanism of amide formation is a source of insight into the properties of carboxylic acids and amines. Initially, we might expect an amine to act as a base and simply accept a proton from the carboxylic acid. Indeed, that does happen, and a quaternary ammonium salt is formed when the reagents are mixed in the absence of a solvent. For example,... 

---