Aggregating particles

The hot mixes are designed by using a standard laboratory compaction procedure to develop a composition reflecting estabUshed criteria for volume percent air voids, total volume percent voids between aggregate particles, flow and stabdity, or compressive strength. Tests such as the Marshall, Unconfined Compression, Hubbard-Field, Triaxial Procedure, or the Hveem stabdometer method are used (109). 

Soot. Emitted smoke from clean (ash-free) fuels consists of unoxidized and aggregated particles of soot, sometimes referred to as carbon though it is actually a hydrocarbon. Typically, the particles are of submicrometer size and are initially formed by pyrolysis or partial oxidation of hydrocarbons in very rich but hot regions of hydrocarbon flames conditions that cause smoke will usually also tend to produce unbumed hydrocarbons with thek potential contribution to smog formation. Both maybe objectionable, though for different reasons, at concentrations equivalent to only 0.01—0.1% of the initial fuel. Although thek effect on combustion efficiency would be negligible at these levels, it is nevertheless important to reduce such emissions. 

In summary, dispersants are effective for particle dispersion and crystal growth inhibition, but do not normally have surface-active properties such as oil emulsification. Chelants and antiprecipitants frequently inhibit crystal growth better than dispersants, but are ineffective for particle dispersion. Flocculants are effective for aggregating particles, the opposite function of a dispersant. 

AM I NO ACIDS A microscopic filter is attached to the IV line when amino acid solutions are administered. The filter prevents microscopic aggregates (particles that may form in the IV bag) from entering the bloodstream where they could cause massive emboli. 

Figure 7.5 Two topologically distinct types of mesoporous gold sponge, each with 50 volume % gold, (a) Swiss-cheese morphology produced by de-alloying, (b) aggregated particle morphology produced by sintering of nanoparticles.

Fig. 2.8 Time series of mean marine snow concentration [kmolP/m3] (solid), number of aggregates [particles/cm3] (dashed), and the mean slope of the particle size distribution in the euphotic zone (solid), and number of aggregates (dashed) at 175W 55°S.

The lower pressure causes coalescence of gas particles, which decreases their kinetic energy. Accordingly, the impact between the aggregate particle and the container s walls is less violent, which lowers the observed pressure. 

Pores are found in many solids and the term porosity is often used quite arbitrarily to describe many different properties of such materials. Occasionally, it is used to indicate the mere presence of pores in a material, sometimes as a measure for the size of the pores, and often as a measure for the amount of pores present in a material. The latter is closest to its physical definition. The porosity of a material is defined as the ratio between the pore volume of a particle and its total volume (pore volume + volume of solid) [1]. A certain porosity is a common feature of most heterogeneous catalysts. The pores are either formed by voids between small aggregated particles (textural porosity) or they are intrinsic structural features of the materials (structural porosity). According to the IUPAC notation, porous materials are classified with respect to their sizes into three groups microporous, mesoporous, and macroporous materials [2], Microporous materials have pores with diameters < 2 nm, mesoporous materials have pore diameters between 2 and 50 nm, and macroporous materials have pore diameters > 50 nm. Nowadays, some authors use the term nanoporosity which, however, has no clear definition but is typically used in combination with nanotechnology and nanochemistry for materials with pore sizes in the nanometer range, i.e., 0.1 to 100 nm. Nanoporous could thus mean everything from microporous to macroporous. 

Transmission electron microscopy micrographs (Fig. 13.24) also indicate an important characteristic of the supported particles. As in the case of suspensions, they are either aggregated or isolated. Support surface properties may he an important factor governing this aggregation. After deposition on the support, we observed that samples prepared from acidic hydrosols are characterized by the presence of aggregated particles constituting flocculates ranging from 10 to 200 nm, whereas samples prepared via basic hydrosols contain only isolated particles. The opposite was observed when hydrosols were concerned. These final states of the supported particles may be controlled... 

Spray pyrolysis routes have been extensively investigated to prepare Pt-based catalysts. Typically, a liquid feed of metal precursor and carbon is atomized into an aerosol and fed into a continuous furnace to evaporate and heat-treat to form a collectable powder. The method has good control over final aggregate particle size and metal particle size distributions, as well as producing powder without further isolation or separation. Hampton-Smith et al. have reviewed efforts of Superior MicroPowder (now Cabot Fuel Cells) in this area. ... 

---