Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Adhesive removal

The main forces liable to be exerted on fine particles are calculated in Table I. We can see from this table that the two main parameters that drive the particle adhesion-removal mechanisms are the van der Waals and electrostatic forces. [Pg.193]

Whereas microneedles are designed to pierce through the outer layers of skin, the controlled destruction or adhesive removal of the stratum corneum represent alternative methods for overcoming the penetrative barrier to cutaneous drug delivery. [Pg.346]

Adhesive remover 1- propanol, 1-propoxy-2-propanol, 8 2- propanol, tripropyleneglycole... [Pg.353]

Print table adhesive remover. Used to remove print table adhesives or renew adhesive surface tackiness. Minimal odor development in use. [Pg.394]

Printing ink cleaners/Ink press washers (replacing toluene) Adhesive removers (replacing acetone)... [Pg.106]

Use A sealant and adhesive removal solvent, useful for surface preparation for prepaint and prebonding, general surface cleaning and degreasing. [Pg.1130]

Trichioroethane is used in some adhesive remover pads of incubators in intensive care nurseries, and there is evidence that infants in incubators can be exposed to high concentrations of... [Pg.162]

Adhesive remover 1-Propanol, l-propoxy-2-propanol, 2-propanol, tripropylene glycol 8... [Pg.222]

Chem. Descrip. Blend of nonaromatic hydrocarbons Uses Solvent cleaner for electronic components, engineering, fabrication (flux and adhesive remover), printing (excess ink remover), coatings (excess resin remover), aerospace (manual cold degasser) Features Evaporates to leave no residue very high flash pt., useful as nonflamm. solv. in most applies. [Pg.508]

Uses Solvent cleaner for electronic components, engineering, fabrication (flux and adhesive remover), printing (excess ink remover), coatings (excess resin remover)... [Pg.667]

Ricinoleic acid adhesive removal agent d-Limonene adhesive rubber Chlorobenzene adhesive solvent, plastic toys Toluene... [Pg.4794]

Zestron VD/ Zestron Modified alcohol Flux residue and SMT adhesive removal 40°-45°C (spray-in-air stencil cleaning) N/A 170-175 27.9 N/A 62 0.76 (20 C)... [Pg.177]

Zestron SD 301/ Zestron Modified alcohol cleaning agent Solder paste and SMT adhesive removal horn PWBs and stencils/screens N/A 150-170 26.1 N/A 47 1.5(20 C)... [Pg.177]

Axarel 2300/ Petroferm Propylene glycol ether-based cleaning agent (KB value >150) Solder paste and adhesive removal (20%-30% in water) from stencils and misprints N/A 3 N/A 62 0.5 (20 C)... [Pg.184]

X30C NC paste, NC flux, and adhesive removal stencils, boards N/A Solvent/ semi-aqueous Single solvent... [Pg.194]

AQ-201SC Semi-automatic ultrasonic (40 kHz) stencilcleaning system for solder paste and adhesives removes rosin (R, RMA, and RA), water-soluble (OA), and no-clean pastes Stencil wash, stencil wash plus, stencil wash AD SMT, stencil cleaner N/A N/A... [Pg.195]

Figure 1 Infrared transmission spectra of (A) polyethylene/poly(ethylene terephthalate) laminate (B) separated poly(ethylene terephthalate) layer (C) separated polyethylene layer plus adhesive and (D) separated polyethylene layer with adhesive removed. Figure 1 Infrared transmission spectra of (A) polyethylene/poly(ethylene terephthalate) laminate (B) separated poly(ethylene terephthalate) layer (C) separated polyethylene layer plus adhesive and (D) separated polyethylene layer with adhesive removed.
In the surface mount assembly process, type 11 and type III boards will always require adhesive to mount the SMDs for passage through the solder wave. This is apparent when one envisions components on the bottom side of the substrate with no through hole leads to hold them in place. Adhesives will stay in place after the soldering process and throughout the fife of the substrate and the product, since there is no convenient means for adhesive removal once the solder process is complete. Additionally, adhesives can be used to enhance both thermal and electrical conduction between device features and board features. This means use of an adhesive must consider a number of both physical and chemical characteristics ... [Pg.1306]

Uses Microemulsifler, surfactant for dibasic ester soivs. detergent, rinse aid for degreasers, graffiti removers, paint removers, adhesive removers, solv.-based cleaners... [Pg.271]

Uses Emulsifier for industrial soivs., aromatics, DBE soivs., d-limonene, Exxate soivs., kerosene, min. spirits, pine oil, terpenes detergent, wetting agent, rinse aid for solv.-based cleaners, adhesive removers, paint strippers, transportation cleaners, waterless hand cleaners, solv.-based degreasers Pmperties Cl. liq. pH 6.0 (10%) 90% solids Cola Mulse ECA [Colonial Chem ]... [Pg.271]

Poly-Tergent RCS-43 rinse aid, acid cleaners Cola Terge LFD-C Cola Terlc MSC-NA rinse aid, acid systems Cola Terlc MSC-NA rinse aid, adhesive removers Cola Mulse DBE Cola Mulse DLE Cola Mulse ECA Cola Mulse SBC Cola Mulse TRP... [Pg.2745]

See other pages where Adhesive removal is mentioned: [Pg.350]    [Pg.123]    [Pg.291]    [Pg.522]    [Pg.219]    [Pg.150]    [Pg.163]    [Pg.2400]    [Pg.900]    [Pg.900]    [Pg.6723]    [Pg.370]    [Pg.380]    [Pg.66]    [Pg.277]    [Pg.271]    [Pg.1047]    [Pg.2194]    [Pg.2580]    [Pg.2825]   
See also in sourсe #XX -- [ Pg.70 ]



SEARCH



Correlation Among Friction, Adhesion Force, Removal Rate, and Surface Quality in Cu CMP

Thermoplastic adhesives removal methods

© 2024 chempedia.info