Adhesion retention

The contrasting modes of failure were photographed for Figure 21. Adhesive retention by the fabric caused the glossy blackness of the right hand sample. Prop. Add. is an abbreviation for proprietary additive and refers to the crossbridging agent. 

Solomon, T.S., Adhesion Retention of Tire Cords Using Caiboset Resins in Cord Adhesives, presented at the Rubber Division ACS Meeting, Atlanta, GA, March 27, 1979. 

The first interface occurs between the spray solution and the atmosphere (air) and determines the droplet spectrum, rate of evaporation, drift, etc. The second interface occurs between the liquid droplets and the leaf surface. The droplets impinging on the surface are subject to a number of processes which determine their adhesion, retention, and further spread. The nature of the deposit formed is governed by the rate of droplet evaporation and the concentration gradient of the surfactant across the droplet. 

The method used to apply and dry a fixative affects the degree of stiffness and hold it imparts to the hairstyle. If appHed and then manipulated with a comb, bmsh, or fingers as the polymer forms its film, the adhesive bonds between the hair are broken, the film coating the hair is broken, and the end result is a soft feel with Htde set retention. If the fixative is allowed to dry undisturbed, then the result is a firmer feel and better hold. 

Polyimides (PI) were among the eadiest candidates in the field of thermally stable polymers. In addition to high temperature property retention, these materials also exhibit chemical resistance and relative ease of synthesis and use. This has led to numerous innovations in the chemistry of synthesis and cure mechanisms, stmcture variations, and ultimately products and appHcations. Polyimides (qv) are available as films, fibers, enamels or varnishes, adhesives, matrix resins for composites, and mol ding powders. They are used in numerous commercial and military aircraft as stmctural composites, eg, over a ton of polyimide film is presently used on the NASA shuttle orbiter. Work continues on these materials, including the more recent electronic apphcations. 

Additional improvements have been incorporated since 1966 with the availabihty of thinner float glass. Glass thickness and interlayer thickness have been studied to optimize the product for occupant retention, occupant injury, and damage to the windshield from external sources (30,31). The thinner float glass windshields are more resistant to stone impacts than the early plate glass windshields. The majority of laminated windshields are made of two pieces of 2—2.5 mm aimealed glass and 0.76 mm of controlled adhesion interlayer. 

Oxane bonds, M—O—Si, are hydroly2ed during prolonged exposure to water but reform when dried. Adhesion in composites is maintained by controlling conditions favorable for equiUbrium oxane formation, ie, maximum initial oxane bonding, minimum penetration of water to the interface, and optimum morphology for retention of silanols at the interface. The inclusion of a hydrophobic silane, such as phenyltrimethoxysilane [2996-92-17, with the organofunctional silane increases thermal stabiUty of the silane and make the bond more water resistant (42). 

Poly(vinyl alcohol) is used as an additive to dry-wall joint cements and stucco finish compounds. Rapid cold-water solubiUty, which can be achieved with finely ground PVA, is important in many dry mixed products. Partially hydrolyzed grades are commercially available in fine-particle size under the name S-grades. The main purpose of the poly(vinyl alcohol) is to improve adhesion and act as a water-retention aid. 

Primers for Metal. If reasonably high performance is required ia the end product and unless cost is of paramount importance, a minimum of two coats, usually a primer and a top coat, should be appHed to metal. For highest performance, primer vehicles should provide good wet adhesion, be saponification resistant, and have low viscosity to permit penetration of the vehicle iato microsurface irregularities ia the substrate. Color, color retention, exterior durabiHty, and other such properties are generally not important ia primers. Resia systems such as those including bisphenol A epoxy resias which provide superior wet adhesion can thus be used ia spite of their poor exterior durabiHty. 

Resin cements have excellent aesthetic quahties and are essentially insoluble in mouth fluids. Compressive strength is low, but can be increased by the addition of fillers. They have no inherent adhesion to the tooth. Retention is dependent on mechanical locking when the cement flows into irregularities on the surfaces of the substances being cemented. 

There are some aspects in the raw dry NR grades for adhesive manufacturing to be considered. NR tends to suffer oxidative degradation catalyzed by metals (mainly copper). The susceptibility of NR to oxidation can be measured using the plasticity retention index. The better grades of rubber have the higher plasticity retention index. 

Effect of laminating pressure (during I min) on tack retention of a CR adhesive... 

---