Worksheet from

Figure 6.5 Example Pump Time-related Failure Rate Data Worksheet. From Science Applications International Corporation.

It follows these steps (1) select the design criteria from a worksheet [Table 7-18(a)] and check off only the major criteria across the worksheet, keeping it simple but realistic (2) refer to the selection chart [Table 7-18(b)] and transfer the bold-faced numerical rating in each selected criteria column to the worksheet, for example, if toughness is one criterion, list 6,4,1, 2, 4, and 2 on the worksheet from top to bottom in the toughness column (3) add up the numbers across the worksheet... 

GO GET NORMAL RANGES WORKSHEET FROM EXCEL FILE proc sql ... 

The attached worksheet from MathCad ( 1986-2001 MathSoft Engineering Education, Inc., 101 Main Street Cambridge, MA 02142-1521) is used for computing the statistical parameters and graphics discussed in Chapters 58 through 61, in references [b-l-b-4]. It is recommended that the statistics incorporated into this series of Worksheets be used for evaluations of goodness of fit statistics such as the correlation coefficient, the coefficient of determination, the standard error of estimate and the useful range of calibration standards used in method development. If you would like this Worksheet sent to you, please request this by e-mail from the authors. 

The worksheet can be made easier to look at by adding lines that separate the column labels and numbers. To create a line under the labels one moves the cell pointer to cell C7, type then =. In LOTUS the backslash ( ) serves as a repeating label prefix. Whatever is typed after the backslash is repeated until it fills the cell. After pressing RETURN cell C7 now contains a row of equal signs ( = ). To continue the double line across the worksheet from cell C7 to cell 07 one can use the / Copy Command. 

Prior to startup one must check certain machine conditions and process control that should be listed on some kind of worksheet from the machine manufacturer, plastic supplier, and/or the more important plant setup person with experience (Chapter 3). Checkup includes the... 

To open an existing workbook or worksheet from the desktop, simply double-click on it. This will open the document (and will start Excel as well if it wasn t already running). If you start Excel first, it will open a new blank workbook. 

To use the Across Worksheets option in the Fill submenu, you must have selected multiple sheets beforehand. Select adjacent or non-adjacent sheets in the same way you select cells. To select an adjacent range of worksheets click on the tab of the first sheet, then hold down the SHIFT key and click on the tab of the last sheet in the range. To select non-adjacent sheets, hold down the CONTROL key (Windows) or the COMMAND key (Macintosh) while selecting. When you choose Across Worksheets from the submenu, the Fill Across Worksheets dialog box (Figure 1-18) will appear you can choose to fill Contents, Formats or both. 

Prepare a spreadsheet similar to the one shown in Figure 3-7 for the gravimetric determination of nickel using dimethylglyoxime. See Section 37B-3 for details. Use the worksheet from Problem 3-9 to calculate the molar mass of Ni(DMG)2 if it is available. 3-4. Write an Excel formula using the FIND and MID functions to eliminate the square brackets and the uncertainty from the atomic mass of lithium in the lUPAC table and display the numeric characters of the atomic weight. 

Sure, said Julia warmly. Let s go get the worksheet from Mrs. Bowes. ... 

Insert copies of the two-electron worksheets from fig5-14.xls. Since sto-3g) basis sets are located at each hydrogen site, the only difference in the permutations leading to the (ij kl) terms rests with the values of Ra, Rb, Rc and Rd, As with the helium calculation, there are S individual terms worked out on each worksheet. Details from the individual two-electron worksheets are shown in Figure 6.8a. 

Procedure—phase E. (This is a repetition of the overview above, but with more detailed explanations.) On copies of the blank worksheets from tables 8.5 and 8.6, at line [b] enter the average furnace temperature for each of the 7 groups of 3 increments that you plotted on your graph, figure 8.5, as a result of procedures C and D. Because our example is for one-side heating, skip lines [c] and [1], Estimate the average load surface temperature for the first group of 3 increments, and enter it on line [d]. 

The following is a brief worksheet from the OSHA SHARP program that is divided into the... 

The LOPA Worksheets are presented below. Notice how the PFD, which determines the target SIL, is obtained, in each worksheet, from ratio of the Maximum tolerable risk to the column called Intermediate Event Likelihood (actually a frequency). 

To protect the woiksheet, choose Protect Worksheet... from the Tools menu, shown in the bottom part of Fig. 6.34. Worksheet protection comes in three levels presented by switches Protection Level in the Protect Worksheet dialog box. The first level, File, the lowest one, protect the worksheet from being saved in some formats, for example as earlier Mathcad versions. Figure 6.35 shows two lists of file formats for saving the current worksheet even without protection level File. In Mathcad 12, this protection level makes it impossible to save the worksheet as Mathcad 11, 2000i, or 2000. 

Fig. 6.35 Protection of a worksheet from saving it as an earlier Mathcad version...

Nevertheless all these steps were incomplete. It is better to install Mathcad itself than download rater bulky Mathcad Explorer, the limitted-version. On the other hand, we want not only to access and read Mathcad worksheets from the Internet rather html or MathML copies, but change the data inputs and see (print, save) new results. 

MAS remains the traditional optirai of downloading the worksheets from servers to improve or extend them (which should referenced appropriately). Thus, the site of this book contains references, pictures (pic), Mathcad files (mcd), and MAS documents, as was noted in the preface... 

The Act ivate method tells the current VBA program that any further references to an object (Range, for example) refer to cells of the active worksheet. Effectively, this statement makes the current worksheet the active one. For Excel files with multiple worksheets, this can be an important distinction. A VBA program with this statement in it can then be invoked from any of the worksheets, and all references to, for example. Cells (I, J) refer to objects within the worksheet from which the VBA program is executed. In other words, if the VBA program was created while Sheet 1 was active and later it is used when Sheet 2 is active, then Ce 11 s (l, J) refers to cells on Sheet 2. Without the Activate command, the cells in Sheet 1 would be referred to by default. 

---