Versus molarity

Third, picking the point on the cui ve of retention versus molar mass where 90 percent falls is inexacl . The retention cui ve usually bends in a way that makes picking the 90 percent point somewhat arbitraiy. 

FIGURE 1.7.5 Octanol -water partition coefficient versus molar solubility (liquid or supercooled liquid) for mononuclear aromatic hydrocarbons. 

I Mixtures Relative Reactivity versus Molar Equivalent Ratio. 

NV Mixtures - Rdative Reactivity versus Molar Equivalent RaUo. 

Sol Fraction versus Molar Equivalent Ratio. Exposure Dose 60 mj/cm. ... 

Fig. 10. Dependence of the charge carrier mobilities in PVC-TNF [54] a electrons (1) and holes (2) versus molar concentrations of the TNF-PVC at the electric field strength 10s V-cm 1. b holes versus mean distance r between nonbound in complex carbazole groups...

Surface pressure/area isotherms of mixtures of the cationic lipid (20, n = 12) with distearoylphosphatidylcholine (DSPC) are shown in Fig. 30. For all mixtures only one collapse point is observed. The collapse pressure increases continuously with increasing amount of DSPC, indicating miscibility of the two components. Plotting A versus molar ratio (Fie. 3D results in considerable deviation from linearity, which also suggests miscibility of the two compounds in monolayers. This is also confirmed by the fact that the polymerization rate, as measured by the increase of optical density at 540 nm, is reduced by a factor of 100 when the DSPC molar ratio is increased from 0 to 0.52,... 

FIGURE 7.3 Osmolality/molarity versus molarity plots for the DMDBTDMA, ra-dodecane system contacted with water at 60°C. (From L. Martinet, Organisation Supramoleculaire des Phases Organiques de Malonamides du Precede d Extraction DIAMEX. PhD thesis. Rapport CEA-R-6105, 2005. With permission.)... 

Figure 7. Antioxidative activity versus molar ratio of arginine to xylose. 100 jxL of 1 100 dilution of crude.

Figure 13.10 Toughness (K C) and toughening mechanisms of epoxy networks modified with 10 phr CSR versus molar mass between crosslinks, Me (O) neat systems ( ) with 10 phr CSR. (Adapted from Lu, 1995.)...

Fig. 5.10. Calculations of the properties of olivine solid solutions (see Ottonello, 1987, for full details and data sources) (a) Calculated phase field boundaries in the system (Mn,Mg),Si04 full circles are calculated boundaries, dashed curves are extrapolated, dotted lines are experimental solubility gap. (b) Plot of site occupancy versus molar composition along the binary join (Ni,Mg)2Si04-...

For dilute solutions, surfactant activity equals concentration, and F is calculated from the plot of 7 versus molar concentration. 

FIGURE 7.13. Etch rate versus molarity for 23 °C on the (100) surface. Data for n- and p-type Si samples were virtually the same. After Glembocki et (Reproduced by permission of The Electrochemical Society, Inc.)... 

FIGURE 7.49. (a) Etch rate and roughness versus molarity for 23 "C, unstirred, HE + H2O rinse (several minutes), (b) Etch rate and roughness versus molarity for 23 °C, stirred, HF rinse + H2O wash (several minutes). (Reprinted with permission from Palik et 1991, American Institute of Physics.)... 

Three different sodium hydroxide solutions are prepared. Let their volumes be Vj, V2, and V3. The relationship between their mole versus molarity numbers are shown in the graph. 

Figure 2.3.1. Pressure versus molar composition for various nonideal binary mixtures with respect to Raoult s law (solid line).

---