Thermodynamic properties density

Physical and thermodynamic properties density and refractive index, thermal and electrical conductivity, hygroscopicity, melting points, free energy and chemical potential, heat capacity, vapor pressure, solubility, thermal stability... 

In this article, we review the historical development of steam tables and then describe the current international standards as maintained by the International Association forthe Properties of Waterand Steam (lAPWS). While the primary focus of steam tables (and therefore of this article) is thermodynamic properties (density, enthalpy, entropy, etc.), other properties (such as viscosity, thermal conductivity, and dielectric constant) are also of some importance and will be mentioned briefly. 

Properties of Liquids 4 3.1 Thermodynamic Properties of Liquids 43.1.1 Liquid Densities... 

Properties of Gases 4 4.1 Thermodynamic Properties of Gases 4.4.1.1 Gas Density... 

Two simulation methods—Monte Carlo and molecular dynamics—allow calculation of the density profile and pressure difference of Eq. III-44 across the vapor-liquid interface [64, 65]. In the former method, the initial system consists of N molecules in assumed positions. An intermolecule potential function is chosen, such as the Lennard-Jones potential, and the positions are randomly varied until the energy of the system is at a minimum. The resulting configuration is taken to be the equilibrium one. In the molecular dynamics approach, the N molecules are given initial positions and velocities and the equations of motion are solved to follow the ensuing collisions until the set shows constant time-average thermodynamic properties. Both methods are computer intensive yet widely used. 

The mineralogical, structural, physical, and thermodynamic properties of the various crystalline alumiaa hydrates are Hsted ia Tables 1, 2, and 3, respectively. X-ray diffraction methods are commonly used to differentiate between materials. Density, refractive iadex, tga, and dta measurements may also be used. 

Physical Properties. Sulfur dioxide [7446-09-5] SO2, is a colorless gas with a characteristic pungent, choking odor. Its physical and thermodynamic properties ate Hsted in Table 8. Heat capacity, vapor pressure, heat of vaporization, density, surface tension, viscosity, thermal conductivity, heat of formation, and free energy of formation as functions of temperature ate available (213), as is a detailed discussion of the sulfur dioxide—water system (215). 

A study on the thermodynamic properties of the three SO phases is given in Reference 30. Table 1 presents a summary of the thermodynamic properties of pure sulfur trioxide. A signiftcandy lower value has been reported for the heat of fusion of y-SO, 24.05 kj /kg (5.75 kcal/kg) (41) than that in Table 1, as have slightly different critical temperature, pressure, and density values (32). 

Equations 175 through 179 allow calculation of thermodynamic properties from volume-expHcit equations of state, ie, equations expHcitiy solvable for volume. If an equation of state is solvable expHcitiy for pressure but not for volume, then alternative formulas must be used, where p is molar density and subscript p/n = 1/E indicates constancy of total volume. Eor equations 180, 181, and 183, T and x are constant for equation 182, Tis constant. 

The solubilities of Li, Na, and Ca hypochlorites in H2O at 25°C ate 40, 45, and 21%, respectively. Solubility isotherms in water at 10°C have been determined for the following systems Ca(OCl)2—CaCl2, NaOCl—NaCl, and Ca(OCl)2—NaOCl (141). The densities of approximately equimolar solutions of NaOCl and NaCl ate given in several product bulletins (142). The uv absorption spectmm of C10 shows a maximum at 292 nm with a molar absorptivity of 350 cm ( 5)- Heats of formation of alkali and alkaline earth hypochlorites ate given (143). Thermodynamic properties of the hypochlorite ion ate ... 

Generalized charts are appHcable to a wide range of industrially important chemicals. Properties for which charts are available include all thermodynamic properties, eg, enthalpy, entropy, Gibbs energy and PVT data, compressibiUty factors, Hquid densities, fugacity coefficients, surface tensions, diffusivities, transport properties, and rate constants for chemical reactions. Charts and tables of compressibiHty factors vs reduced pressure and reduced temperature have been produced. Data is available in both tabular and graphical form (61—72). 

Theoretical and structural studies have been briefly reviewed as late as 1979 (79AHC(25)147) (discussed were the aromaticity, basicity, thermodynamic properties, molecular dimensions and tautomeric properties ) and also in the early 1960s (63ahC(2)365, 62hC(17)1, p. 117). Significant new data have not been added but refinements in the data have been recorded. Tables on electron density, density, refractive indexes, molar refractivity, surface data and dissociation constants of isoxazole and its derivatives have been compiled (62HC(17)l,p. 177). Short reviews on all aspects of the physical properties as applied to isoxazoles have appeared in the series Physical Methods in Heterocyclic Chemistry (1963-1976, vols. 1-6). 

From Water Density at Atmospheric Pressure and Temperatures from 0 to 100°C, Tables of Standard Handbook Data, Standartov, Moscow, 1978. To conserve space, only a few tables of density values are given. The reader is reminded that density values may he found as the reciprocal of the specific volume values tabulated in the Thermodynamic Properties Tables subsection. 

Data on the gas-liquid or vapor-liquid equilibrium for the system at hand. If absorption, stripping, and distillation operations are considered equilibrium-limited processes, which is the usual approach, these data are critical for determining the maximum possible separation. In some cases, the operations are are considerea rate-based (see Sec. 13) but require knowledge of eqmlibrium at the phase interface. Other data required include physical properties such as viscosity and density and thermodynamic properties such as enthalpy. Section 2 deals with sources of such data. 

Thermodynamic Properties The variation in solvent strength of a supercritical fluid From gaslike to hquidlike values may oe described qualitatively in terms of the density, p, or the solubihty parameter, 6 (square root of the cohesive energy density). It is shown For gaseous, hquid, and SCF CO9 as a function of pressure in Fig. 22-17 according to the rigorous thermodynamic definition ... 

Comparing Examples 2a and 2b we notice that the total air pressure has effects on the humidity x, partial density of dry air p total pressure or pressure of humid air, and enthalpy h. Knowing the total pressure is therefore essential in calculations of the thermodynamic properties of humid air. 

Finally, we assume that the fields 4>, p, and u vary slowly on the length scale of the lattice constant (the size of the molecules) and introduce continuous approximation for the thermodynamical-potential density. In the lattice model the only interactions between the amphiphiles are the steric repulsions provided by the lattice structure. The lattice structure does not allow for changes of the orientation of surfactant for distances smaller than the lattice constant. To assure similar property within the mesoscopic description, we add to the grand-thermodynamical potential a term propor-tional to (V u) - -(V x u) [15], so that the correlation length for the orientational order is equal to the size of the molecules. 

An alternative is to consider the value of the thermodynamic property per unit mass. Such quantities are called specific properties. Thus the specific volume is the volume per unit mass. It is the reciprocal of the density and is an intensive property. 

A condition of phase equilibrium is the equality of the chemical potentials in the two phases. Therefore, at all points along the two-phase line, //(g) = p( ). But, as we have noted above, the approach to the critical point brings the liquid and gas closer and closer together in density until they become indistinguishable, At the critical point, all of the thermodynamic properties of the liquid become equal to those of the gas. That is, Hm(g) = Um(g) - /m(l),... 

The form of equations (8.11) and (8.12) turns out to be general for properties near a critical point. In the vicinity of this point, the value of many thermodynamic properties at T becomes proportional to some power of (Tc - T). The exponents which appear in equations such as (8.11) and (8.12) are referred to as critical exponents. The exponent 6 = 0.32 0.01 describes the temperature behavior of molar volume and density as well as other properties, while other properties such as heat capacity and isothermal compressibility are described by other critical exponents. A significant scientific achievement of the 20th century was the observation of the nonanalytic behavior of thermodynamic properties near the critical point and the recognition that the various critical exponents are related to one another ... 

The thermodynamic properties of magnesium make it a natural choice for use as an anode material in rechargeable batteries, as it may provide a considerably higher energy density than the commonly used lead-acid and nickel-cadmium systems, while in contrast to Pb and Cd, magnesium is inexpensive, environmentally friendly, and safe to handle. However, the development of Mg-ion batteries has so far been limited by the kinetics of Mg " " diffusion and the lack of suitable electrolytes. Actually, in spite of an expected general similarity between the processes of Li and Mg ion insertion into inorganic host materials, most of the compounds that exhibit fast and reversible Li ion insertion perform very poorly in Mg " ions. Hence, there... 

The purpose of this compilation is to tabulate the densities of compounds, hence only minimal description of experimental methods used to measure the density of liquids or solids appears. Detailed descriptions of methods for density determination of solids, liquids and gases, along with appropriate density reference standards, appear in a chapter by Davis and Koch in Physical Methods of Chemistry, Volume VI, Determination of Thermodynamic Properties [86-ros/bae],... 

Proceeding conceptually for a moment without these logistical difficulties, once we have determined the density of states we can calculate thermodynamic properties at any temperature of interest. The average potential energy is... 

---