Super Abrasion Furnace

SAF = super abrasion furnace ISAF = intermediate super abrasion furnace. [Pg.545]

SAF = super abrasion furnace ISAF = intermediate super abrasion furnace HAF = high abrasion furnace FEF = fast extrusion furnace ... [Pg.550]

Abbreviation for intermediate super abrasion furnace carbon black. [Pg.35]

Abbreviation for super abrasion furnace grade of carbon black. See Furnace Black. [Pg.55]

SAF - Super abrasion furnace, ISAF - Intermediate super abrasion HAF - High abrasion furnace, FEF - Fast extmsion furnace SRF - Semi reinforcing furnace HS - High structure, LS - low structure, HM - High modulus ... [Pg.143]

The surface area of blacks ranges from 20 m2/cm3 (N990 - Medium thermal black) to 225 m2/cm3 (N110 - Super abrasion furnace black). [Pg.143]

Intermediate-Intermediate Super Abrasion Furnace (I-ISAF) 240... [Pg.272]

Figure 3.5 shows a plot of hardness against volume fraction of filler [ISAF (intermediate super abrasion furnace) black] in the vulcanizate base on the rubber compound formulations shown in Table 3.1. Hardness is defined as the resistance to surface indentation as measured under specified conditions. It is a non-destructive test that measures the reversible deformation when an... [Pg.113]

Super-abrasion furnace black SAF NllO Oil furnace 17 145 High reinforcement used in special and olf-road tyre products for which high abrasion resistance is required. [Pg.215]

Fig. 7.3. Effect of carbon black fillers on properties of a mi liable polyurethane elastomer. MT= Medium Thermal Carbon Black, SRF= Semi-Reinforcing Carbon Black, HAF= High Abrasion Furnace Carbon Black, ISAF= Intermediate Super Abrasion Furnace Carbon Black.

Sujith et al. carried out rheometric studies of intermediate super-abrasion furnace (ISAF) carbon black loaded NR/EVA composites of different blend compositions. A higher maximum torque value was found for high EVA loaded samples and this is attributed to the increase in crystallinity in them. EVA is semicrystalline, and so restricts the mobility of the macromolecular chains. [Pg.290]

HA = High abrasion furnace ISAF = Intermediate super abrasion furnace MOR = 2-(4-morpholinyl mercapto)-benzthiazole Accinox ZC = N-(l,3 Dimethyl butyl)-N-phenyl-p-phenylenediamine Vulkanox HS = Polymerised 1,2 dihydro-2,2,4-trimethylquinoline Accitard RE = N-cyclohexyl thiophthalimide ... [Pg.151]

The barrier properties of 70/30 acrylonitrile-butadiene mbber/ethylene propylene diene monomer rubber (NBR/EPDM) vulcanizates, when loaded with carbon black fillers [e.g., I SAP (intermediate super-abrasion furnace), HAF (high-abrasion furnace) and SRF (semi-reinforcing furnace)] and using benzene, toluene and xylene as penetrants, have been examined with reference to the type of filler employed [66]. The filled samples were found to exhibit a better resistance to uptake of the three organic solvents when compared to the respective unfilled blends for any given blend ratio. With regards to the three types of carbon black used, solvent uptake was in the order SRF-> HAF-> ISAF-filled samples. The reason for this order was attributed to the better filler reinforcements and enhanced crosslink densities of the matrix as the size of the carbon black particles used was decreased. A similar behavior was also identified for NR/EVA composites [52]. [Pg.441]

ISAF Intermediate super abrasion furnace black... [Pg.538]

N (normal curing), SAP (super abrasion furnace), ISAF (intermediate super abrasion furnace), HAF (high abrasion furnace), CF (conductive furnace), GPT (general purpose tread),... [Pg.27]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...