Stress-raising effects

A considerable reduction in stress concentration could be achieved by using a cross-bore which is eUiptical in cross-section, provided the major axis of the eUipse is normal to the axis of the main cylinder. A more practical method of achieving the same effect is to have an offset radial hole whose axis is parallel to a radius but not coincident with it (97,98). Whenever possible the sharp edges at the intersection of the main bore with the cross bore are removed and smooth rounded corners produced so as to reduce the stress raising effects. 

These values are determined by experiment. It is, however, by no means a trivial task to measure the lamina compressive and shear strengths (52,53). Also the failure of the first ply of a laminate does not necessarily coincide with the maximum load that the laminate can sustain. In many practical composite laminates first-ply failure may be accompanied by a very small reduction in the laminate stiffness. Local ply-level failures can reduce the stress-raising effects of notches and enhance fatigue performance (54). 

Fig. 8.3 Schematic representation of the stress corrosion cracking mechanism of the pit (after Pickering and Swann ). (a) Tubular pits initiated at solute-rich slip step. The pits may, but need not necessarily, follow the slip plane once they are initiated, (b) Ductile tearing along a plane containing the tubular pits. The stress is increased across the plane because of the reduced cross section and the stress raising effect...

However, it is also recognised that the overall flexibility of the joint is as important as its strength. This is valid if the stress raising effect of the hard point , created by the presence of the leg. Is to be avoided. Thus the designer is faced with apparently contradictory requirements that of strength (requiring a thick overlaminate) and that of flexibility (requiring a thin overlaminate). 

Susceptibility of austenitic stainless steels to this form of corrosion usually becomes a problem when the caustic concentration exceeds approximately 25% and temperatures are above 100 °C (212 °F). Because welding is involved in most fabrications, the weld joint becomes the focus of attention because of potential stress-raising effects and because of high residual shrinkage stresses. Cracking occurs most often in the weld HAZ. 

Physical aging (annealing the glass at temperatures close to, but below, the glass transition temperature) is known to raise the shear yield stress Its effects... 

Public education is a primary tool in current speed moderation strategies in Australia, but needs supplementing with additional messages. One common theme is to raise the level of knowledge about the effects of small increases in impact speed on crash likelihood and injury severity. A second theme is to emphasise the probability of detection and punishment. The third common theme is to stress the effects of severe injury on lifestyle. While all are appropriate, they run the risk of reinforcing the unpopularity of intense enforcement of low-level speeding. 

Bikerman [182] criticized the derivation of Eq. X-18 out of concern for die ignored vertical component of On soft surfaces a circular ridge is raised at the periphery of a drop (see Ref. 67) on harder solids there is no visible effect, but the stress is there. It has been suggested that the contact angle is determined by the balance of surface stresses rather than one of surface free energies, the two not necessarily being the same for a... 

Tests in a Clj + Oj mixture at 427°C have shown that the worst elements for promoting susceptibility are Al, Sn, Cu, V, Cr, Mn, Fe and Ni, while the least harmful are Zr, Ta and Mo. a-phase alloys are generally more susceptible than )3-phase alloys. Heat treatment has not been examined extensively, but some heat treatments render some a-alloys more susceptible or change the mode of fracture. The general effect will depend upon the alloy and the heat-treatment cycle. Subsequent cold work can sometimes considerably lower susceptibility. Failure times decrease as either the testing temperature or initial stress value is raised. 

It may be felt that the initiation of a stress-corrosion test involves no more than bringing the environment into contact with the specimen in which a stress is generated, but the order in which these steps are carried out may influence the results obtained, as may certain other actions at the start of the test. Thus, in outdoor exposure tests the time of the year at which the test is initiated can have a marked effect upon the time to failure as can the orientation of the specimen, i.e. according to whether the tension surface in bend specimens is horizontal upwards or downwards or at some other angle. But even in laboratory tests, the time at which the stress is applied in relation to the time at which the specimen is exposed to the environment may influence results. Figure 8.100 shows the effects of exposure for 3 h at the applied stress before the solution was introduced to the cell, upon the failure of a magnesium alloy immersed in a chromate-chloride solution. Clearly such prior creep extends the lifetime of specimens and raises the threshold stress very considerably and since other metals are known to be strain-rate sensitive in their cracking response, it is likely that the type of result apparent in Fig. 8.100 is more widely applicable. 

Le Chatelier s principle When a stress is applied to a system in dynamic equilibrium, the equilibrium adjusts to minimize the effect of the stress. Example a reaction at equilibrium tends to proceed in the endothermic direction when the temperature is raised, leveling The observation that strong acids all have the same strength in water, and all behave as though they were solutions of H,Of ions. 

The effects of heat and/or water stress can be determined experimentally by raising animals at high temperatures with reduced water intake. This study reports on experiments designed to test the heat and water stress hypothesis. 

Eleven controlled diet and environment experiments have been designed in a way that can be used to investigate the effects of protein nutrition and heat and/or water stress on diet-tissue A N. Laboratory rats were raised on purified, pelletized diets in which the isotopic composition of proteins, lipids and carbohydrates were well characterized and their proportions accurately and precisely measured (Ambrose and Norr 1993). Four experiments involved manipulation of temperature and/or water availability. Of these four experiments, one used a diet with high (70%) protein concentrations and heat/water stress (36°C) and three used normal (20%) protein concentrations. Seven experiments were conducted at normal temperature (21°C) with water ad libitum. Of these seven experiments, two used diets formulated with veiy low protein (5%), three with normal protein and two with high protein concentrations. 

---