Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Single stage compression

For simplicity and reduced cost, an adsorption storage system using single stage compression is attractive, which puts a practical upper limit to the adsorption... [Pg.272]

Gun propellant and compressed gas are the most widely used energy sources. In single-stage, compressed-gas systems velocities can be achieved from perhaps 30 ms to 1.5 kms These compressed-gas gun systems are the most widely used as they are quite safe and can be incorporated into typical university and industrial laboratories. A typical compressed-gas gun experimental configuration is shown in Fig. 3.5. [Pg.59]

F = an allowance for interstage pressure drop = 1.00 for single-stage compression 1,08 for two-stage compression 1.10 for three-stage compression Qg = flow rate, MMsefd... [Pg.271]

Avoid single-stage compression for very low temperatures. [Pg.356]

Figure 8.40. Single-stage compression cycle—-with clearance... Figure 8.40. Single-stage compression cycle—-with clearance...
In single stage compression, the compression ratio Is limited to about 4. [Pg.16]

From the values of y and the pressure ratios, it is clear that the pressure ratio for ammonia is very high for a single-stage compression. The guidelines for gas compression given in Chapter 13 indicate that propylene and propane compressions should be able to be achieved in a single compression stage, but the ammonia would seem to require two compression... [Pg.538]

The pressure ratio is a little high for Cycle 2 to be carried out in a single compression stage. However, single-stage compression... [Pg.541]

Theoretical horsepower for isentropic single-stage compression... [Pg.553]

Vacuum Pump Type Iniet Flow Rate " m /h Single-Stage Compression Ratio Minimum Suction Pressure ... [Pg.202]

With adiabatic compression, the final temperature T (degrees Fanrenheit absolute) is given by the formula T = Ti(p2/pi)° for single-stage compression by... [Pg.147]

Centrifugal compressors can operate at speeds from 9,000 to 50,000 rpm, with single-stage compression ratios from 1.2 to 9, and efficiencies from 30 to 85%, depending upon the specific design and application. [Pg.453]

Liquids are less compressible than gases, so their high-pressure equipment needs only a single-stage compression this is usually provided by an air-operated actuator (Fig. 7.13). [Pg.333]

The work destroyed in the single-stage compression is very much greater than the work... [Pg.109]

Figure 7.4 Single-stage compression, (a) Initial state, (b) Final state, (c) Work destroyed in a single-stage compression, 1/1/=... Figure 7.4 Single-stage compression, (a) Initial state, (b) Final state, (c) Work destroyed in a single-stage compression, 1/1/=...
Process . Single-stage expansion with P p = P2, then single-stage compression with - op Pi ... [Pg.111]

Figure 8.39. Single-stage compression cycle — no clearance... Figure 8.39. Single-stage compression cycle — no clearance...

See other pages where Single stage compression is mentioned: [Pg.273]    [Pg.433]    [Pg.696]    [Pg.890]    [Pg.891]    [Pg.264]    [Pg.208]    [Pg.31]    [Pg.192]    [Pg.168]    [Pg.170]    [Pg.172]    [Pg.208]    [Pg.430]    [Pg.1289]    [Pg.100]    [Pg.109]    [Pg.110]    [Pg.147]    [Pg.515]   
See also in sourсe #XX -- [ Pg.350 ]




SEARCH



Compression stage

Compression staged

Single stage compression, with clearance

Single-stage

Stage compressive

© 2024 chempedia.info